best part cooling fan duct 3d models

This is a beta version for a V6 hotend mount featuring provision for a 40mm hotend cooling fan, as well as 5015 part cooling designed specifically for the Creality range of printers. The duct has been optimized using CFD to ensure effective part...

Yet another part cooling improvement for the Solidoodle mk2, using Lawsy's NEW replacement carriages. This design will fit a 40x40mm radial fan, which has much better flow, when compared to those little 30x30 axial fans. Printed @ 0.15 Layer...

These custom cooling fan ducts replace the factory part on the LEO, providing superior airflow to the nozzle. The original ducts may look well-made, but they fail miserably in their cooling duties, simply blowing air at the heater block and behind...

I struggled finding a part cooling fan that would fit because Tronxy keeps changing things. So I hacked up a custom solution. The ring sits close to the heat block, but printing PLA hasn't caused any issues so far as long as the silicone sock is in...

Upgrade your device's cooling system by replacing the conventional 30x30 fan with a more powerful 40x40 fan to maintain optimal temperature.

This design accommodates a third 40mm fan for enhanced active cooling. By circulating air from multiple directions, I aimed to optimize print quality and overcome the limitations of single-source airflow, which previously hindered my prints. To...

Own project. ...Duct for side fan. Very thin. Watch out for thin walls and support. I've used small magnet glued for holding fi8x2. ...If needed there is a place for additional fi4x2 (common used in USB plastic cases)

I'm building a fresh start on a brand new fan duct for my trusty Sovol SV01. ...The printing process is underway and I'll share the first images as soon as possible.

edited 2019 01 28 added version 4 - semicircular 6 way edited 6/12/2018 added version 3 4 way fan duct for anet a8 i am not sure this is better than all the other, but i like "squared" designs. i am using it without issues since i printed to...

Edited 2019 01 28 Added version 4 - Semicircular 6 Way Edited 6/12/2018 Added Version 3 4 Way Fan Duct for Anet A8 I'm Not Sure This is Better Than All the Other, but I Like "Squared" Designs. I Am Using It Without Issues Since I Printed. To...

I have modified cooling from Prusa i3 to sort of fit on Prusa MINI Obviously its not awesome, but its better than the original one (or at least thats what i think :D ) i wanted it to be in the back so you can easily acces and see the nozzle, also its...

Another fan duct that fits perfectly within the fan housing, providing a clearer view of the nozzle. Prints flawlessly without requiring any support structures. ... Print Settings: Printer: Anet A8 Rafts: None Needed Supports: Not Required Resolution:...

... If you only have one duct, orientate the shroud so the bottom edge of the level sensor mount is pointing towards your existing part cooling fan by rotating the Z axis in your slicer. The same goes for the cooling duct – overhang it towards the fan.

Design Features - The Tuct Tunnel uses aerodynamic principles of aircraft airfoil to enhance the flow of cooling air in air tunnels. ... - New ducts use silicon air tubes to prevent heat dissolution at the heatend and to be flexible in collisions with...

Create an easy-to-print, 40mm fan duct for your Rostock Max 3D printer using OpenSCAD. ...Print it in PLA without needing support material, then secure it to the platform with three cable ties threaded through its top holes and air outlets (as shown in...

I obtained this design from a Cr10s Pro cooling fan and adapted it for use on a Sovol printer. ...To prevent warping, I recommend using either PETG or ABS filament.

A redesigned fan duct was created, one that is both shorter and thinner, yet still mounts in the original hotend cooling fan mounting spot. The printer uses ABS material, printing vertically at a .2mm layer thickness with 1mm thick walls. ...This...

This was done by offsetting the fan at a greater distance from the stepper with a directional duct. The result is that the printer now moves more air around the motor instead of pushing it backward, making it work much more efficiently. I can tell...

Notable changes: • Fans positioned more normal to nozzle array than original to improve airflow and decrease pressure drop before air enters the nozzle array • Nozzle array diameter increased to decrease pressure drop through the array • Radiused...

This fan duct directs air in front of and behind the nozzle with three separate air streams for more even cooling and better overhangs on all sides of the nozzle. Works well for me between 20 and 40% fan speed for most models. My overhangs are much...

Cut the printed duct to match your required length.

Summary: I noticed that most of the air was being pushed back instead of around the stepper motor in u/chrismagno's design, so I moved the fan further away from the motor with a directional duct to move more air around it. This change seems to work...

Disclaimer: These versions of the FanDuct won't receive any updates or adjustments! . FOR IMPROVED PERFORMANCE USE THE NEW V4 INSTEAD: https://www.thingiverse.com/thing:4886226 . . . . . I designed this Fan Duct after upgrading my CR10 with the...

(9-25-21) Rev.2 Standalone can be used without the stock heat break metal shroud in case you have modded your heatbreak cooling fan and no longer use the stock metal shroud. It will mount directly to the X-carriage using one M3 screw. (10-29-21)...

This is a remix of Creality Ender 5 Part Cooling Fan Duct by ShaunTheBaa April 05, 2020 Update to version 2b adds clearance for the silicone hot end boot and improves the left hand fixings. Images to be updated shortly. ...

Introducing the no-frills, no-strings duct your SV01 will become an instant fan of :D. Designed with PETG in mind. A sagging-resistant design, it will not bump into your prints. Minimal path air flow that will not cool the nozzle. It has a built-in...

Hello dear Artillery Community I have found a solution for an unplaced fan, for which you don't have to rebuild half of the printer and still have a perfect view of the nozzle from the front. Cooling from both sides with the Upgrade!! It wortks for...

...NOTE: this has to be printed with support on buildplate on. The radial fan is suppose to be press fitted onto the duct, after it has been bolted to the underside of the Lawsy carriage. If this for some reason does not hold, add a drop of super glue.

This design was tailored to accommodate a third 40mm fan for active cooling. I achieved this by aiming to circulate air evenly around the print. The previous setup, with air coming solely from the front, didn't meet my requirements. This design...

Combined two different Files https://www.thingiverse.com/thing:4692181#Summary and https://www.thingiverse.com/thing:4408571 adjusted the fan duct nozzle to be a little lower and smaller and added the Fan duct so you can use a 40mm fan instead of a...