best part cooling fan duct 3d models

Fan duct for Lama3D hot end, also featuring a holder for an M18 capacitive or inductive Z-probe is available.\nDimensional specifications for the Z-probe offset are X:47, Y:-12 (dependent on orientation).\nThe fan duct was printed with PET.\nPrint...

Re-designed from the ground up - inspired by Madau3D's **Ductinator** - I present the Trifecta Fan Duct for 3 fans (40 mm), for the Ender 3 / CR10 for a custom mount that goes on a MG12H linear rail block. This comes with a little standoff block...

... I crafted specifically for my trusty Prusa i3 printer. ...This ingenious design relies on a robust fan, the 4010S Brushless DC Cooling Blower Fan, measuring an impressive 50x40x10 mm. ...Your satisfaction is sure to be achieved with this setup.

... optimal airflow at the nozzle. After numerous iterations of the design, I finally arrived at a final product that delivers perfect airflow. The duct securely attaches to the part cooling fan using the original screws from the stock configuration.

new part cooling fan duct for Anycubic Kobra WIP

Ender 3 V1 Fan Duct for 5015 Part Cooling Fan with CRTouch Mount remixed

Ender 3 V1 Fan Duct for 5015 Part Cooling Fan with CRTouch Mount remixed

Also created a air duct for the part cooling fan as I didn't want it to take radiant warm air from the buildplate. Both piece are easliy printable and don't need supports. After printing the pieces just slide onto the fans, no extra hardware...

Part cooling duct for E3D Hemera.

Remixed in Tinkercad and Windows 3D Builder using mount area from thing 2814127 Replaces stock Ender part cooling fan duct. Printed with supports, bed only, have not tried without supports. ...

This simple duct connects to the side of the heat sink, directing some airflow down close to the part/extruder nozzle for added cooling - especially crucial when printing PLA. The duct is easily clipped in and out of place. ...It's not a remarkable...

Modified part cooling duct to suit a E3D heater block . ...( the original wont fit properly)

Hope my Duct can help someone looking for a cool and functional parts cooling Duct. For this you'll need: 12 M3x30 screws for the 3 fans 2 M3x16 screws to attach the Ducts H mount 3 M3x10 screws to attach the Ducts bar on the top and cable holder 2...

Hopefully, my duct will help someone looking for a cool and functional parts cooling duct. To make this, you'll need: 12 M3x30 screws for the three fans 2 M3x16 screws to attach the Duct's H mount 3 M3x10 screws to attach the Duct's bar on top and...

It integrates with the standard part cooling fan and assembly that comes with the Ender 3.\r\n\r\nI encountered issues with other cooling mods due to their proximity to the nozzle or heater block. ...This led me to design my own mod from...

I modified my Climber7 part cooling fan using "Plasticene" and noticed an improvement using PETG, so I'd thought I'd set about making a STL model to refine the idea. There are some volume constraints with this part within the hot end enclosure, so I...

This is a custom cooling duct designed for the AnyCubic Kossel Pulley version, though it may also work on other varieties of the AnyCubic Kossel.\r\n\r\nThe duct fits exactly into the same four holes as the stock part cooling duct and uses the same...

(I've tightened the leaky nozzle in the photo now.) There's also a version 2 available at http://www.thingiverse.com/thing:1360007, featuring a slide shutter that opens and closes (part close) the cooling duct, making it even easier to switch...

This is a part of a cooling fan, made by me.

Antonio Guardia designed this part cooling fan project specifically for the AGraber 30i.

Quick and dirty remix of the part cooling duct to fit "my" i3 mega bmg direct drive mod. I squished only the middle. ...

This modification allows me to use the screws that secure the hot end mount to the carriage to attach the part cooling duct as well. In the photo, you can see that I printed the part using Colorfabb's remarkable PA-CF filament, which can withstand...

Replacement Part Cooling Duct for the Wombot Exilis - a Universal Fit Solution! This cooling duct is specifically designed to fit the Wombot Exilis and will also work with other compatible models. ...Important: Do not rely on supports when installing...

Hi all,I modified the Satsana Fan duct to mount two noctua 40x40 silent fans.Its based on the V59 version of the fan duct.To mount the part cooler you need some additional M3 screws.I also added some covers for the fans.

***I designed this duct for better part cooling on my Ender 3Originally designed to fit the Bullseye base design, so it is compatible with the Bullseye. The base was designed for better fitment with the Micro Swiss hot end and Direct drive...

Better prints require advanced replacement filament cooling systems, not just any ordinary ducts.

Print instructions After printing and getting rid of support materials, unscrew the screws on the front and bottom of the printhead(behind the heaterblock on the 45 degree angle part), then attach the duct to the printhead using the two screws you...

I found the available fan-attachments for the RF100 take up to much space around the printhead, and also sometimes don't produce enough airflow. This cooling solution utilizes a radial fan design and can be attached to the printhead using already...

A sleek and compact radial component cooling duct designed to efficiently dissipate heat from high-performance systems.

I modified a part cooling duct I discovered on prusaprinters.org, reinforcing the bottom section to prevent warping issues. My experiments revealed that using carbon fiber nylon at .20 mm thickness yielded optimal results, courtesy of Matterhackers...