best filament for ender 3 v2 3d models

BOM: - 2x bearing 6906 (30x47x9mm) or 61906 (30x47x9mm) - 4x M4 nut - 4x M4x8 hexagon socket set screw with cone point Printing: - blockade_2 and blockade_2_nut: print with supports (everywhere) - spacer_1 is optional - clean "cover" after printing,...

************************************************** Tested on my Ender 3 v2, but should work on other Ender models if they use the same t-slot rail design. The extruder part may need to be connected via a different method if on a model that is...

This model is engineered to adapt to your desired location for extruding the filament. A simple slide-over installation is all that's required, as the guide fits snugly over the existing spool mount without needing any additional hardware. The...

Here's an optimized version (for those having trouble with Simplify3d) of the filament guide made by Tomaskom_cz (https://www.thingiverse.com/thing:3095575). All credit goes to him. I took his original design and turned it into a solid, continuous...

This allows you to not need a screw and nut for the guide bearing. Also you don't need to print the inner bearing ring. ...Works with metal extruder upgrade.

I have now converted it into a filament runout sensor and designed a small housing for it.This one is a modification of my 1st version.I rotated the filament path 90 degrees: The filament no longer runs along the microswitch, but across it. This...

... just over the know without the need of removing the spoolholder. ... Remixed from: https://www.thingiverse.com/thing:3975794 Using for the paper spools of "Real Filament" as the paper has a bit more friction. ...Makes prints with paper spools smoother.

I made this filament filter to be used in conjunction with side mounted filament.

This filament guide will properly feed filament to the extruder. ...This will also help smooth pulling of filament from the spool.

A filament cleaner that can be directly attached to the extruder.

Mounted securely onto the Z lead screw, this filament guide offers unparalleled protection for your valuable plastic extruder. Whether you're an experienced maker or a hobbyist, this essential tool will shield your machine from costly damage caused...

Couldnt decide on what filament guide i wanted, so instead I combined two designs i found here on thingiverse. ...Will upload a photo once its done in the printer.

I was having problems holding my almost empty filament roles on the spool holder so I made this. used pla at .24 layer Hight with a 15% infill one suggestion I have if you make this is to wrap duck tape or electrical tape around it once to grip...

Es un soporte para montar el sensor de filamento de la cr-10s en una Ender 3 y además sirve de guía de filamento a la salida del carretel. Yo lo usé en una Ender 3v2. Como opcional, para disminuir el rozamiento, agrandé el orificio de entrada con...

... which was prone to snapping off during use. ...To prevent this, I reinforced it for added durability. I also opted for a 100% infill print, but in reality, you might be able to get by with a lower percentage and still achieve satisfactory results.

Filament guide and dust filter for Creality standard and upgraded extruder.

Remixed to allow 45deg offset for smoother filament flow from spool.

To create a filament runout sensor, use a holder for a limit switch. Cut the middle pin of the switch and then solder pins 1 and 3 to a cable. ...Finally, connect the cable to your printer, as shown in the last picture.You may need a longer M3 screw to...

Modified filament guide clip for use with M5 flat head screw. ...Requires to cut M5 threads in the extrusion piece.

So I built an enclosure and had to detach the original filament holder from the 3D printer frame. ...This 3D print functions as a base for the original filament holder.

So I built an enclosure and had to detach the original filament holder from the 3D printer frame. ...This 3D print functions as a base for the original filament holder. Category: 3D Printer Parts

Combine with thing:4683505 (lower) for a complete the set of no screws, no supports, upper & lower filament guides. ... In the pictures the part is mounted on a modified Filboyt mount found here Update v1.2: Cleaned up the model using Blender If you'd...

Just another filament guide. ...slip on, so no need for any tools or bearings. ...print without support, and put in place

I wanted a simple guide to keep the filament running into the extruder at a better angle and the ones I had seen were a bit too much work for what I wanted (I personally prefer fewer moving parts), so I designed this. Just over an hour to print and...

3cm longer version of the filament feeder to better fit with the https://www.thingiverse.com/thing:4683505 In the original version, the filament goes at a very sharp angle in two places and doesn't come back on the spool for me.

I wanted a simple guide to keep the filament running into the extruder at a better angle and the ones I had seen were a bit too much work for what I wanted (I personally prefer fewer moving parts), so I designed this. ... Just over an hour to print and...

This will stop your filament touching the greasy Z Screw Rod, and also if you run it like I do from my Sunlu filament holder it reduces air and moisture getting to the filament Print to your usual settings for any small print, any material will...

... in one of the photos. My switch dimensions were:12.8mm long, 5.8mm thick, 7.15mm switch collapsed. When soldering switch to connector, be sure to have your orientation worked out.The bearing guide cover was used from another bearing filament guide.

Combine with thing:4683505 (lower) for a complete the set of no screws, no supports, upper & lower filament guides. ... In the pictures the part is mounted on a modified Filboyt mount found here Update v1.2: Cleaned up the model using Blender If you'd...

Update: This design is superceded by my single-roller design over here: https://www.thingiverse.com/thing:5330621 This is an alternate top filament guide for this thingy: https://www.thingiverse.com/thing:3428924/files . You will need two spacers and...