best filament for ender 3 v2 3d models

The roll of filament stays very close to the vertical frame of the printer. ...So I decided to design and print an extension of about 80 mm. Now the distance to the extruder is greater and the filament, from the roll holder is less forced.

Ender 3/Pro/V2 Bigtreetech smart filament sensor adapter. After the direct drive update I couldn't find any good solution for the sensor location. This works perfect for me. And don't have to do any changes to the stoke spool holder.</p> <p>Note:...

... Good for ender 3, v2, or any other printer that uses same profiles as Creality. Left side designed to be exactly same length as the aluminum profile, and right side sticks out a bit. 12cm in length, verify that it not interferes with the z axis.

I printed this https://www.thingiverse.com/thing:3063886 filament guide for my Ender 3 v2, because the filament was scraping the Z lead screw sometimes. However, it's suggested to use 608 bearings with this desing and I didn't have any. Tried to...

I had problems with the original design due to filament drag, there was just a lot of friction, so I simply added a torus ring to the bottom of the cup, to make the filament run smoother through the guide. ...I also changed the orientation of the part...

This bushing gets rid of the "slack" due to the size of the center of the Overture spools and will allow the extruder to more freely feed filament. ...It is a little tricky to slip over the edge of the holder, but once on, the spool will very easily...

This small device helps protect the filament from contaminants such as dust.A piece of sponge, pre-lubricated with a small amount of alcohol, is inserted into the filter.Tighten the cable tie into the special recess located in the middle of the...

I made this spacer because I could not find one that fit the spool on my printer arm. ...This has a larger hole to slide over the spool on the printer. I also made it a bit long so there is not a lot of side to side movement of the role of filament.

I love Filboyt's filament guide, but found that it was jiggling loose from the printer frame. I changed the mounting piece and combined it with the guide to make it much more secure. ... It is pictured in the orientation that it goes on the printer, but...

I found the tube from the Dry Box to the printer is very stiff and does not want to stay close to the extruder so I remixed this so the tube would fit snuggly and keep the filament clean and protected.

I love Filboyt's filament guide, but found that it was jiggling loose from the printer frame. I changed the mounting piece and combined it with the guide to make it much more secure. ... It is pictured in the orientation that it goes on the printer,...

Bluetooth remote holder remixed from crandell 2 to fit the Ender 3 V2 x-axis cover

Bluetooth remote holder remixed from crandell 2 to fit the Ender 3 V2 x-axis cover

I made the model to adapt it to the ender 3 V2

I wanted an enclosure for my Ener 3 pro to print ABS with greater ease. I required a thermal blanket, but it needed additional support, so I designed the Longarms to hold it in place. The spool holder posed a challenge, so I created a holder that...

It happened to me sever times, that filament escaped original guide. ...So I redesigned it to have a spiral that guides.&nbsp;</p><p>There are two versions available, with short or a long arm.</p><p>I added better clip, not a remix, but just a copy - <a...

Bfptouch mount for Ender 3 v2 for Satsana, remix of Onthe9z's mount for CR Touch: https://www.thingiverse.com/thing:4935492 Satsana with Back Support (Ender 3 V2) by willsside: https://www.thingiverse.com/thing:4919570 BFPTouch using Printable Probe...

I only tested it on Ender3 V2, but as you can see, It might suit for any other printer share similar extrusion frame with ender 3. ... Two piece included, need no support, infill 0%, wall thickness and top/bottom thickness both at least 1.2, The...

For 4cm inner diameter spool

... serve me here in the community. ...So to end my concern, I made this model without affecting the vertical movement. My printer is an Ender 3 V2, but it may also work with Ender 3 and Ender 3 Pro. ... * I suggest lubricating the tube internally.

This is a PSU Cover for the Crealety Ender 3 V2 it has the right holes for the switch and the plug Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 2.4 Infill: 20 Filament: 3D Jack ECO Pla PLA Black ...

Added support for a M6 nut to make the tube fitting stay in place. ... **No support needed**

... mount and wheel for use of this bearing. ... Update: added a longer cover for the wheel to accommodate the sightly bigger wheel made, and lessened the diameter of the hole to 6mm to better connect to the 5.91 diameter rod that runs through the bearing.

Just slide into the old spool holder and secure it firmly in place. ...Next, swap out the smaller Dremel spool for a new one and attach it to the shaft. For added durability, increase the infill setting on your device to its maximum capacity.

... for use with this bearing. ... Update: I added a longer cover for the wheel to accommodate the slightly bigger wheel made, and reduced the diameter of the hole to 6mm to improve connectivity to the 5.91 diameter rod that passes through the bearing.

... is the condensed version (70 mm), carefully crafted into a seamless whole. ...I merged all the components, streamlining the narrative for maximum impact. ... 14/01/2020 an updated guide has been incorporated, enhancing the overall viewing experience.

Fits on the stock Ender 3 V2 filament spool bracket. 0.20mm or smaller layer height suggested for bearings and threaded parts, the others can be larger layer height if desired. Orient parts on bed prior to printing. When assembling, leave some...

Mount for filament runout sensor on ender 3 for direct drive when the extruder stepper is moved from the stock location

I bought an SD reader from Amazon, to fit to my Ender 3 v2. I put rails on it, so it would sit on the left side of the base. I made it a fraction bigger to aid fitting the reader. Tightened/fitted by wrapping Masking tape around it. Also on here,...

All the parts needed for ender 3 v2 cable managment with chain links, i remixed multiple models i found online to make what for me was an optimal setup with the least amount of tikering of the printer parts