best filament for ender 3 v2 3d models

I remixed both design and attached them each other. ... ring and spacer are from other design. 608zz bearing, 1 bolt and 1 nut are required to assembly. Thanks for the designs.

I remix this 2 projects for my own https://www.thingiverse.com/thing:4808355 https://www.thingiverse.com/thing:5789436 now i have a movable holder printed with support

... air in the room to about 1-2 inches from this guide to the extruder. Hole is slightly off but finely misses contacting the screw bar for the Z axis. ...I printed on the largest flat side but print whatever way you like and use supports as required.

That is a Filament Guide with filament sensor mount for an ender 3 v2. ...It may also work for other printers, but I haven't tested it.

This is a tool holder for all necessery tools for and from the Ender 3 V2. I didnt like the drawer so i remixed the two tool holder for the end of the Ender. The left hole is for the Sandpaper holder (https://www.thingiverse.com/thing:2976235). I...

I have customized the filament guide for the Ender 3 V2 (Neo). ...Additionally, I have added the feature that makes it easy to insert and remove the filament!

Power is taken from the Ender 3 Power supply itself with the help of a Buck Converter (files are also provided). The lid of the Buck converter is glued together by FeviBond glue (a rubber-based adhesive), so that the lid is semi-permanent, just like...

Small HSW module with attachment for Ender rails. I've put mine on top of the printer and holds bits and bobs nicely. ...And looks cool while doing so.Check out HSW here:https://www.printables.com/model/152592-honeycomb-storage-wall

Filament Spool for the small roll of filament that's included with Creality Ender 3 V2 printer. The male and female parts snap together, but can be easily detached as the clips are exposed. ... Video demo: https://youtu.be/hmCwrt0vT_g

The design was based on the work of ArdyJay "Filament guide for CR-10S, Ender-3, Alfawise U20, etc." I just made it solid and add the hole for PTFE Tube to make sure the filament won't shave again. I recommend to print using PETG, because i tried...

This is a mount for the BigTreeTech (BTT) Smart Filament Sensor for a Creality Ender 3 v2 with a genuine (not a knock-off) Bondtech BMG 1.75mm extruder. This is a remix of https://www.thingiverse.com/thing:4656838 . I found that thing 4656838 did...

I designed this Filament guide for my Ender 3 V2 to make it easier to load filaments. I upgraded to dual geared extruder many months ago, however it was not particularly easy to thread the filament through the tiny hole and often the filament would...

This is a remix of: 3: https://www.thingiverse.com/thing:4662740 2: https://www.thingiverse.com/thing:4185537 1: https://www.thingiverse.com/thing:3052488 The Original one from BrendanShanahan (thing 3) was build for the Ender 3 V2 with aluminium...

I designed this Filament guide for my Ender 3 V2 to make it easier to load filaments. I upgraded to dual geared extruder many months ago, however it was not particularly easy to thread the filament through the tiny hole and often the filament would...

Coming Soon: I've also created an optional nut for the Ender-3 V2 in case you've lost or broken the original. Attribution: I started with vikke_01's Thing 3334367 as my starting point, but reworked it to my specs and used the stock nut from jaft64,...

This mount provides a rolling Filament Guide (uses a 608 roller-skate/skateboard bearing) which aligns the filament path through the BTT smart filament sensor then directly into the BMG type extruder, when the extruded is mounted in lieu of the...

The PTFE hose must be cut as follows:: === PTFE tube from sensor to extruder: 11cm PTFE tube from filament to sensor: 8cm Material list: ==== PTFE Bowden Hose Micro Swiss Bowden Dual Gear Extruder Creality Filament Runout Sensor Kit Filament I have...

This is for Ender 3 v2 with direct drive setup. Filament sensor mounted on top next to the spool. May have issues if printing too high because filament sensor is stationary while hot end is moving, causing filament coming out of the sensor to bend.

Remixed the Ender 3 cable chain extruder mount by norp (27mm stock version) and added a shelf to mount the Big Tree Tech smart filament sensor to my Ender 3 v2. ... There are two holes in the mount so you can remove two of the factory screws from...

I knocked together a silly filament guide that mounts to the NEMA17 (31x31) plate where the extruder motor used to be on my Ender 3 V2. This is for use with an Ender 3 that no longer has the extruder stepper motor attached to the frame. I recently...

This is for use with an Ender 3 that no longer has the extruder stepper motor attached to the frame. I recently upgraded to an E3D Hemera and had previously switched to a side mounted spool holder so my filament path was kind of all over the place. ...I...

Remixed from https://www.thingiverse.com/thing:4821339 Loved the design, but I had no need for the Z axis guide. ...I used this on an Ender 3 Pro, not a V2, so I removed the text as well. ...Prints easily with no supports required.

For my Ender 3 V2 Neo is out new firmware update for runout filament sensor so I've added this sensor with it's bracket https://it.aliexpress.com/item/1005005372359005.html and I can't mount the left bat of the stibilizers kit I had. I've...

This is a remix of two different filament sensors to make installing the sensor on your Ender 3 / Ender 3 Pro / Ender 3 V2 very easy. Instructions: 1. Use the stock screws that come with the stock z-endstop to install the switch to this mount...

Dies ist ein Filament Guide für meinen Ender 3 V2 Drucker mit Aluminium Dual Gear Extruder. Mich hat es immer gestört, dass das Filament ständig an der Einzugsöffnung entlang schrammt. Deshalb habe ich heute den ganzen kram fast 3 Stunden vermessen...

I designed this for my Ender-3 v2 with the Creality Titan Direct Drive using TinkerCAD, https://www.tinkercad.com/things/jnTaDbgEz4M . I was inspired by the Creality CR-10 Smart Pro FRS mount. My original design did not swivel and caused binding...

This is a remix of Markacho project for Ender 3v2 printer with filament sensor. I change body length and fixing because when you add filament sensor you have different extruder holder. it comes in very tight so use some power to attached it. ...

I designed this for my Ender-3 v2 with the Creality Titan Direct Drive using TinkerCAD, https://www.tinkercad.com/things/jnTaDbgEz4M . I was inspired by the Creality CR-10 Smart Pro FRS mount. My original design did not swivel and caused binding...

I also designed a mount for the Ender 3 printer. No glue is needed, just need: 2 x Neodymium magnet (5x5 mm) 2 x "3x20" flat head screws 2 x M3 nuts 1 x Module detection sensor 1 x small piece of foam 1 x A small piece of PTFE tube (6 mm) to be...

I also designed a mount for the Ender 3 printer. No glue is needed, just need: 3 x Neodymium magnet (5x5 mm) 2 x "3x20" flat head screws 2 x M3 nuts 1 x Module detection sensor 1 x small piece of foam 1 x A small piece of PTFE tube (6 mm) to be...