best ender 3 pro fan duct 3d models

I re callibrated my ender 3 pro, from the flow rate to e-steps to x, y and z movement. After that and running this new fan duct... I got results you see in the pics. ...Running a stringing test i had 0 stringing, was very surprised but also very...

I decided to design a new fan duct with modifications to ensure enough room between print and fan duct as well as broadened the output to avoid too much air cooling in one spot. In my opinion it produced better printing results. ...You are welcome to...

fan duct for ender 3 pro with 40mm fan

fan duct for ender 3 pro with 40mm fan

2in1 Fan duct and part cooling for Ender 3 / 3 Pro Simple and effective design.

Manta redesign https://www.thingiverse.com/thing:4403017 and https://cults3d.com/en/3d-model/tool/manta-compact-fan-duct-tool-change-system from BoothyBoothy for my Ender 3 pro, I wanted to use the factory fans and adapt another one from the same...

Ventilation duct for Ender 3 pro controller board. Necessary for closing the printer (to print ABS), with it the plate can be cooled, just connect a hose. Duto de ventilação para placa controladora Ender 3 pro. ... Necessário para o fechamento da...

Rediseño de Manta https://www.thingiverse.com/thing:4403017 y https://www.printables.com/es/model/169185-manta-compact-fan-duct-tool-change-system de BoothyBoothy para mi Ender 3 pro, quería utilizar los ventiladores de fábrica y adaptar otro del...

Fan Duct for the Creality Ender 3 Series and CR Series This fan duct was copied from the Zortrax M200 because it cools but does not directly hit the nozzle, keeping it stable. Its extrusion filament cooling efficiency is superior to that of the...

Rediseño de Manta https://www.thingiverse.com/thing:4403017 de BoothyBoothy para mi Ender 3 pro, quería utilizar los ventiladores de fábrica y adaptar otro del mismo 4010 para tener doble ventilador de capa. ... Tornillería: Tornillos 8mm y tuercas ...

Remix of Gabriel3DCaster's "CR-10 Fan Mod - Airflow Optimization" I redesigned the original setup because it was bumping into my Ender 3 Pro's silicone cover, causing warping issues. ...To resolve this problem, I modified it to be slightly taller,...

This is a remix of https://www.thingiverse.com/thing:3676132/files designed to slide over the stock fan bracket on the ender 3 with my Volcano hot end. ... 4x m4 screws One of the screws holding the stock cooling fan on 60mm fan

=============================================================== Introducing a Fresh Take on the Part Fan Cooler Duct This innovative duct is specifically designed to elevate ABS/PLA printing. It boasts three key functions that work in harmony to...

277 / 5.000 Vertaalresultaten I designed this because the stock fan duct was no longer blowing air where it should with my MK8 hot end. I also designed it in such a way that the hot end fan no longer overrules the cooling part fan. ... Must be printed...

WIP Had issues with overhangs, not being printed nicely at the back of the models, so I wanted to try with circular fan duct. Couldn't find one, built one on my own. I printed it vertically, using tree support, build plate only. ...I also used brim...

also filled some grooves inside the duct cause they were causing thin wall conditions Used the MS 3d builder so it doesnt look clean but it does the job I printed it at 45deg, with no inside supports to minimize bridging, looks like it would also...

The original duct was lower than my nozzle, so I shortened it. There are 2 versions, the "flat" one and the 2mm one. ...The flat one, once installed will be tilted to point down towards the print, the other will be perpendicular to the nozzle.

I had a problem with the ears that hold the fan on the original so I added some reinforcements

Modified holes to 4mm in order to use brass inserts, the original holes where 5mm (too big) DOES NOT NEED SUPPORTS Suggested Settings 3 Layer Walls 75% Infill PLA is ok, the heat does not reaches from the nozzle/hotend Nonetheless if you want more...

# Yeah, I said what I said # Up for grabs is what is (in my personal opinion) one of the easiest, best hot end upgrades you can make for your Ender 3 / Ender 3 Pro / CR10(?) (I think it's the same hot end mount, but do verify before printing). The...

I've edited and upgraded my Ender 3 Pro printer to include a dual fan duct, specifically designed for use with 5015 fans, which provide direct drive capabilities.

Fan duct for Ender 3. This is a personal file, maybe not suitable for every user. Project is still in progress. ...Use at your own risk.

Ender 3 fan duct for nozzle, the stock one doesn't blow below nozzle tip rather than at the nozzle sock.

Project to fan duct Ender 3 without screws, this model was thinked use with fan axial. without supports (see photos). ... follow me social networks @mundoem3d my web site mundoem3d.com

A Fand Duct Made for ender 3 with Micro Swiss Direct drive Should fit ordinary Ender 3 also.. ...:)

Updated the design made [Tevo Tornado Round Fan Duct for 5015 Blower](https://www.thingiverse.com/thing:2842573) to fit on an Ender 3 Pro with a Silicon cap.

A simple Ender 3 / Pro fan duct to attach a Noctua 40x40x20mm (Noctua NF-A4x20 FLX) fan instead of the original one. The original part-cooling fan can be attached on the right side. You can use all the original screws. Be careful: The Noctua Fan...

Here is a simple fan duct that can be used to replace the original one on an Ender 3, printing out in about thirty minutes. ...It prints easily with PLA without any issues because it does not get too close to the hotend, and I believe directing air flow...

This fan duct should fit every Creality printer with the same hot end base plate like the one used for the Ender 3 pro. The back plate is necessary the keep the air flow away from the heating block. Modifications: -Hook added to fan mount to mount...

https://www.thingiverse.com/thing:3864519 https://www.thingiverse.com/thing:3115750 Creality Ender 3 Pro stock hot end mount for 5015 fan duct. I had to turn the 5015 to fit with my direct drive upgrade. This was printed on my Ender 3 Pro. I have...