best ender 3 cooling duct 3d models

There are slight improvements on the bottom of the split in the Y and X.I'm planning a V2 to reduce the footprint of the duct as well as another Noctua cooling solution to cool the heatsink ( its very tricky/impossible with an axial flow fan)A note...

The cooling duct employs a 24V 5015 fan that moves more air than the stock fan, so I've decreased my cooling fan speed to accommodate its increased airflow. At some point, I may redesign the cooling duct because it obstructs visibility of the nozzle...

This is a remix from superpotatofudge's [CR-10 40mm Stock Hot End Cooling Duct](https://www.thingiverse.com/thing:2160958). I redesigned the thing with radii that match the Noctua NF-A4x20 fan. Also replaced the original hot end attachment with...

I updated BHMarten's design by stripping away the cable holder and Ender 3 logo, opting for a cleaner aesthetic that suits my taste.

The design underwent a significant change, as it frequently came into contact with the heater block, leading to damage at best and print failures at worst. To rectify this issue, I lengthened the main duct and added a reinforcing tower on the...

The accessory is specifically designed for the Ender 3 and comparable models, attaching securely to the side of the standard extruder casing. ...Several similar designs are already available on Thingiverse, but this one raises the fan a notch higher,...

Remixed From https://www.thingiverse.com/thing:3495189 Wanted the minimalist way of getting a 5015 blower fan dual cooler onto my OEM ender 3. This screws on in place of the original blower fan. Use a 20mm M3 Bolt/Screw and Lock Nut to secure the...

Remix of DEJello's Duct. ...I loved the design but it hit the screw on the far end so I shifted the mounting plate over a little.

I remixed the settings to match my Ender 3 Pro purchased in December of 2019. You may need to check the original files if your printer requires a second set of tabs. No built-in supports are available, so external support is necessary. I use 10%...

... ...All credit should go to SignalSpirit! I made it a bit shorter and slightly angled down from inside the duct to help air flow hit the print better. ...I had an issue where the original design would blow above the print causing bridging issues.

... I've created an attachment that's easy to install. Simply print both components without supports and then attach them together using the fan duct. ... Before setting this up, make sure to remove the small built-in support from the bottom part.

Print with Tree support but look for NO SUPPORT INSIDE of the part cooling channels. You may never remove them from the part after the print ^^ I have created another Design, but I noticed, that it did not perform very well. So I remixed an...

Lowered down fan so the heat sock can fit in without pressing against the fan duct (does require some support for a decent print, I recommend using tree supports and using them on baseplate only, this is up to you...

Simple nozzle cooling air duct modification for Ender 3 Neo or Ender 3 V2 Neo, to provide improved and even cooling from all sides. ... Very clean and simple print with no supports needed This is a remix to fit Ender 3 neo printers from: DJIFF Edit:...

Initially this was made just for fun, but it turned into a cool duct and now is the one i use on my Ender 2. I believe that this can be used on the CR10 also but never tried. Hope my Duct can help someone looking for a cool and functional parts...

To make this, you'll need: 12 M3x30 screws for the three fans 2 M3x16 screws to attach the Duct's H mount 3 M3x10 screws to attach the Duct's bar on top and cable holder 2 40x20 fans The Hot End is screwed directly to its mount like originally. ...

In addition to its primary function of cooling the extruder, the Ender 5 Plus Extruder Cooling Duct also serves as a protective barrier against dust and debris that can compromise your prints. By shielding the hotend from unwanted particles, you'll...

Remixed in Tinkercad and Windows 3D Builder using mount area from thing 2814127 Replaces stock Ender part cooling fan duct. Printed with supports, bed only, have not tried without supports. ...

This is a Remix of Ender Jet Cooling Duct, it also fits CR-10, 10S, S5, among others. I did a remix on these two because there was a gap, an opening between two walls. In the top half of the included picture (the 3 version is on left, the 4...

I took a popular design, the Ender 5 Cooling Duct created by McGybeer, and gave it a fresh spin. First things first, I stripped away the original logo to give this print some personality all its own. However, during the assembly process, one of the...

Made this remix in preparation of getting a second 5015 fan for my Ender 3 S1 PRO since I couldn't find any other that was suited for me. I'm a total noob at CAD or 3d editing, so I just went for the straight cut/copy/paste mode with Microsoft 3D...

The purpose of this part is to distribute the air a little bit better than the stock duct is capable of. No additional parts are necessary however I recommend using a heat sheild between the hotend and this component. ... PLA+ 0.16MM Layer height ...

Ender 2 Pro / Ender 3 - 5015 part cooling fan duct with easy to install magnetic mount. Compatible with separate CR touch mount. Minimalist, compact and flexible design. This design has considered easy remix of your own mount for other printers. -...

Newer Ender 5s may come with a slightly different part cooling fan featuring flush-mounted tabs. However, these new(?) fans have tabs designed to sandwich that get in the way of the old parts. I simply edited off the tabs to ensure it fits without...

The Ender 2 is engineered to work seamlessly with a high-quality 12V 50mm radial fan, specifically designed for optimal airflow. This compact fan measures 50X50X15mm and operates at a stable DC 12V voltage. ... For your convenience, the following link...

Printed Components (1 Component): 1x Cooling Duct with LED Extra Components (3 Components): 1x LED Chip COB 12V (Found on Ebay / See image as reference) 1x 100 Ohm Resistor [Amazon Resistor Assortment...

This is a high airflow cooling duct for the Ender 3/3 PRO and CR-10 This design enables conversion from bowden tube to direct drive link to buy the 2 blower fans:...

The stock cooling fan that comes on the original Ender 3 is pretty bad, so when mine died I replaced it with a coaxial fan, and designed this fan duct for part cooling. It is simple, and way more effective. I rarely even have the fan speed above...

Ender 3 V1 Fan Duct for 5015 Part Cooling Fan with CRTouch Mount remixed

Ender 3 V1 Fan Duct for 5015 Part Cooling Fan with CRTouch Mount remixed