best 5015 fan for ender 3 3d models

This is for an Ender3v2 with BLTouch installed. I used: 4020: 4 M3 x 20mm Socket Cap Hex Bolts 5015 1 M3 x 20mm Round Head Hex Bolt X Bracket Clamp 2 M2 x 8mm Round Head Hex BoltPrint Settings Rafts: No Supports: YesResolution: 200 Infill: 20...

* Added some material to the front 5015 fan mount * Added a longer boss for the rear 5015 fan mount with a hole for optional #4-40 or 3mm screw. ...(I don't use one) * Added optional Red Squirrel logo fan guard * Tweaked screw fits and clearances on the...

Mounts a 5015 fan for the heat break and moves the cr touch inline with the nozzle on the left side. ...Clears the gantry.Set heat break fan to 50% fan speed for ultra quiet operation.X-Offset is -50.7

Mounts a 5015 fan for the heatbreak and moves the cr touch inline with the nozzle on the right side. Clears the gantry. Set heatbreak fan to 50% fan speed for ultra quiet operation. You will need to extend the CR Touch wires. ... x offset=37.687

Mounts a 5015 fan for the heatbreak and moves the cr touch inline with the nozzle on the right side. Clears the gantry. Set heatbreak fan to 50% fan speed for ultra quiet operation. You will need to extend the CR Touch wires. ... x offset=37.687

Simple 5015 fan mount and duct for the Ender 5 Plus.  Compatible with the stock metal shroud & bl-touch mount and does not interfere with stock x-stop or belts. ... Only necessary modification is to remove one of the mounts on the 5015 blower fan...

This is a new 360° fan duct to add a 5015 blower to a stock ender 6 printhead.

This hotend assembly enables the use of a Noctua 4010 fan as for cooling the heat break and two Sunon 5015 blowers for part cooling. NOTE: ALL FANS LINKED BELOW ARE 12V, THE ENDER USES 24V! PLAN ACCORDINGLY AND EITHER STEP YOUR VOLTAGES DOWN OR RUN...

A housing for a Noctua 40x20mm hotend fan, designed to work with original mounting holes and blower fan on Ender 3/Ender 3 Pro.

... fan and extruder fan. I chose to use Noctua 40mm x 20mm fans. Check out my other Ender 3 & 3 Pro Upgrades: Ender 3 & 3 Pro - LCD PCB Case Ender 3 & 3 Pro - Scraper Holder Ender 3 & 3 Pro - Spool Holder Ender 3 - Rear Drawer Noctua 60mm Fan Mount

16/02/2022 Major Update: Titanator Version 2 Changes: Reduced the number of parts Significantly increased structural rigidity The bed leveling sensor has been completely redesigned Added support for Volcano hotend Fixed the gaps between the air duct...

Mine is printed as follow: PETG 245 C 4 or 5 walls cubic infill (about 35%) tree support touching build plate only (make sure your support is touching all of the needed places (higher resolution slicing can help that, See picture for my tree support...

Red Squirrel Ender 3 V2/EZABL mount

Fan shroud for the Ender 3 Belt

Cpu Fan Cover for Ender-3.

... a stock hotend with the Creality hot end fix done and it shortened the z axis height. If you have one, this duct works to adapt it to the ender 3 but I did not see the value in it and tossed it in the trash after using it for about 3 months. ...

Requires 5 M3 nuts and bolts to assemble The BLTouch mount is rigidly fixed, with a hole reserved for its cable BLTouch Offset: X: -37 Y: -35 This mount uses NEMA 17 21mm-24mm stepper motors; for thicker ones, there's a version without the left...

Hi, I've been using this BantaMount re-design for quite a while and decided to share it with everyone else!Firstly I had to slightly redesign the basic mounting system to fit the Ender 3 Max by removing a part and adding two screw holes to the...

I was having trouble finding a low profile 5015 fan duct for my Ender 5. The 5 appears to have a wider extruder carriage plate than the 3, and other designs I found were either gigantic or did not clear the carriage plate. Seems to be working better...

In addition, you will need: A 5015 fan, preferably running on 24 V power Two neodymium magnets with a diameter of 10 mm and a thickness of 3 mm One 3x20mm screw and nut for securing the fan A plug connector compatible with either 12V or 24 V (e.g.,...

... the fan duct (Hero_Me_lightweight_Dual_5015_Ducts_Gen3). ... To rectify this issue, I modified the design. The required Hero Me files are: * Hero_Me_Base_for_Ender_5_Gen3a * Hero_Me_lightweight_Dual_5015_Ducts_Gen3 * BLTouch_Wing_Dual_fan_Ender_5_Gen3

Air duct mod for stock fan Ender 3. ...

This is my remix for Ender 5 with 5015 fan. Fan is slightly rised so it doesnt hit the frame on min X movement. Duct profiles are also modified (both inside and outside) for easier overhang printing. If you want to use the screw on the back my...

Your printer should have more than enough cooling power for the bridging required for this print. Remember, keep this part as light as possible, infill should only be 10%-15%, go with max 3 walls, if you can do 2 to keep to weight down. Update...

Remix Satsana for Ender 3 V2 with fan for filament 40x40x20 and fan for hotend 40x40x10

... the Satsana with this type of Direct Drive Plate Adapter. It needs Supports (Normal / Touching Buildplate Only) for the BLT part and the Cutted Cable Wall Original File from DWO is here https://www.thingiverse.com/thing:4910842 Happy Printing.

A lightweight fan duct for ender 3 for stock 4010 fans with better heatsink airflow.

I no longer have the V2 Neo, but these were the last changes I made to these shrouds which gave me the best look/fitment.

I like the original idea of simplicity and easy to print. ... I make a remix to add another 5015 fans on the left side. The water test is amazing. ... Thanks for the great design.

I remixed this thing to see x bar level according to the bed for when its need some tuning on machine. Also i can track for any misaligments of bar after a period of usage. ...