bernina 830 record 3d models

small modification of the orignal ... a little bit larger ... ...a little bit "rounder"

<p>small modification of the orignal ... a little bit larger ... ...a little bit "rounder"</p> Category: Fashion

I picked up a Bernina Record 830, and what caught my eye was that the repair module on the left had been fixed, but the previous owner snapped off the clear plastic clip that kept the wire in place. I decided to create a replacement model instead of...

This is a replacement light assembly plate for the back of the Bernina Record 830 door. The machine I recently purchased had undergone previous repairs, and the owner accidentally broke the plate, which caused the entire assembly to wobble slightly...

This is a replacement cover for the type 290 foot control on later model Bernina Record 830 sewing machines. The original cover had broken clamshell clamps and a damaged tab that dragged the carbon tracer pin carrier up and down, while the carbon...

Replacement part for the Bernina 830 record I just bought. This part was broken. The screws thread in place in the 4mm holes just as in the old part. ... It fits perfectly.

I wanted a handle for my Bernina 830 I just bought because I didn't have the original transport case. The trick was to create an attachment that would be removable and would sit above the center of gravity for easy handling. After quite a lot...

Storage cases for thread bobins, cable and pedal. ...

The sewing machine Bernina 530 Record has also different motors most of which are also similar in style to the PSE-4C. It almost looks as if the assembly which holds the brushes was the same all along so there is a high chance tha caps will fit also...

Nockenstapelgetriebe für Bernina-Nähmaschinen 730, 732, 830, 831, 832, 840, 850 To replace the broken plastik part or use it as negativ for a mold

Bypass ring/upper thread guide for the sewing machines BERNINA 730/731/732 Record. Used in machines produced after March 1964. Take a piece of (copper) wire, bend it into a nice shape and glue it into the slit of the part. ...you can then just clip...

Nockenstapelgetriebe für Bernina-Nähmaschinen 730, 732, 830, 831, 832, 840, 850To replace the broken plastik part or use it as negativ for a mold

Nockenstapelgetriebe für Bernina-Nähmaschinen 730, 732, 830, 831, 832, 840, 850To replace the broken plastik part or use it as negativ for a mold.

For the machines BERNINA 730/731/732 Record, other might work as well. You can replace the standert one by removing it, inserting this one and fasten it with two tiny screws (the original ones will not work). You have to remove the hooks of the...

The second variant has a small hole the same size as the Bernina shaft, this can be imported to TinkerCAD and you can put in whatever size hole you want but I found 12.2mm to work well. ... This is a rework of a gear for a 500/600 series Bernina...

Customized version of https://www.thingiverse.com/thing:2770475 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2770475

Customized version of https://www.thingiverse.com/thing:5392290 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5392290

The objective is to create a prototype of the Komatsu_830 utilizing SolidWorks software.

Vinyl record made for 1/6 action figures, might be oversized so you may need to shrink it.

The Komatsu 830 is a powerful dump truck model designed for heavy-duty mining and quarrying operations. This massive machine boasts an impressive payload capacity, making it ideal for transporting large quantities of material over long distances. ...Its...

Bernina Hand Wheel Replacement. ...Modern Bernina clip on hand wheel.

Schraubhilfe für Bernina Hoop s

These are Bernina sewing machine foot holders for the IKEA Skadis pegboard system. ...

This is a specialized bobbin designed specifically for use with large Bernina Jumbo spool sizes.

Bernina Torx Holder Where do you put the little torx screwdriver after chaning the needle? Exactly! ... Print this, attach it to the Bernina and voilà - you have a place to store it!

A 12mm flat fell seam presser foot designed specifically for Bernina machines, easily attaches to the quick change foot stem.

Thread holder for Bernina 730 Embroidery Machine fits multiple models, including yours. ...Replace the existing screw at the back with an M3X40 or M3X45 screw for proper installation.

I made several adjustments to builman's design of the BERNINA bobbin spool tray, effectively streamlining the printing process and eliminating the need for supports.