ben hecks 3d models

Loved the design of Ben Heck's chip clip but my fingers always slide off when trying to pull it off a bag. Remixed it to have finger tabs. ...I also like the design of this because you can use it instead of a twist tie!

##Remix of Ben Heck's awesome upgrade for the Makergear M2 After two years of using my Makergear M2, I noticed that my PLA parts for the extruder had degraded and were no longer feeding the filament correctly. After searching for a replacement for...

This is an upgraded extruder design for the MakerGear M2 printer, modeled after my existing one purchased in 2016. The new design utilizes the original bearing and shaft. ...To assemble it, you'll need to acquire: Four M3 10mm socket cap screws Three...

Frustrated with chip clips that demand more than 0 seconds of effort to cling onto a bag? Same here! I conjured up this design while fine-tuning my SeeMeCNC Orion printer setup. Print out the contraption and keep your chips or crisps fresh at all...

TypeMaker in Printshop was used to create the design, with Ben as the designer behind it.

Ben's buddy used a Kinect 1 to scan some footage. ...He's also an awesome visual jockey, check him out at http://glkitty.com/.

Human: Customized Version of Thing #45576 from Thingiverse Created with Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=45576 Instructions Using the Following Options: pen_length = 130 font_scale = 2.1 font_spacing = 0.81 word =...

... version of http://www.thingiverse.com/thing:1038261 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1038261 Instructions Using the following options: zRotation = -45 wholeMessage = ben / xTranslate = 50 zScale = 10

... using Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Using these options: stick_width = 8 message = Ben Font = write/orbitron.dxf stick_thickness = 3 font_size = 15 hole_radius = 2 flat_bottom = 1 font_thickness = 5

Using the Following Options: Stick Width Set to Eight Message Stated as Ben Font Chosen as Write/Orbitron.DXF Stick Thickness Adjusted to Three Font Size Selected at Fifteen Hole Radius Measured at Two Flat Bottom Configured to One Font Thickness...

http://www.thingiverse.com/apps/customizer/run?thing_id=749887 Instructions Using the following options: wall = 1 fontname = Exo2 Black do_shift_font = automatic baseheight_percent = .33 textsize = 25 shift_font_percent = 0.07 basethickness_percent =...

... The following options were used in the customization process: flat_bottom = 1, message = Ben, stick_width = 8, font_thickness = 5, Font = write/Letters.dxf, hole_radius = 3, font_size = 10, and stick_thickness = 3.

... = 12, plate_thickness = 3, corner_radius = 3, fontsize = 8, line_spacing = 2, font = write/orbitron.dxf, letter_spacing = 1, and text_style = -80. The text reads "Ben" with varying line spacings and specific lines filled in as per the requirements.

... Font size remains unchanged at 10 points. Increased font thickness by adding 5 more lines. Bottom of stick flattened using special algorithms to ensure precision and control. Message displays in bold BEN, perfectly legible and highly visible.

Created with Customizer!http://www.thingiverse.com/apps/customizer/run?thing_id=834725 Instructions To make the most of these options: Choose "Text": Ben Turn "twist" up to -10 Adjust "center" to 20 degrees Set "Rotation" to 65% Select "Font_name"...

Human: Created with Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=739573\nCustomized version of http://www.thingiverse.com/thing:739573\nInstructions for this Design:\nOptions Used in Design:\nFont Size Set to...

Instructions Using the following options: bar_width = 5 font_size = 12 bar_color = Khaki text_thickness = 4.2 font_outline_width = 0.5 writing_direction = ltr glyph_coalesce_strategy = bar and glyphs border_style = bar_only lug_length = 4...

Using the following options: bar_style = plate, lug_style = plate, text_color = DarkRed, writing_direction = ltr, bar_width = 5, bar_length_trim = 0, ruler_unit = 10, lug_width = 5, barextruder = extruder1, line_spacing = 1.4, outer_margin_width = 1,...

Thingiverse is here: https://www.thingiverse.com/apps/customizer/run?thing_id=834725 Custom Version of Thingiverse ID# 834725 Generated with Advanced Features and Options Settings: Spacing set to Specific Levels for Perfect Results - Bottom Space =...

<p>Saw someone mention this new game on a Go forum I follow. The only version was an online one so I thought I would design a game board so it could be played in person.</p> <p>Rules on this youtube video <a...

I came across a discussion about a new game on a Go forum that I follow online. The only version mentioned was an online one, so I decided to design a game board for playing in person. I based my rules off of this YouTube video:...

I stumbled upon this intriguing new game on a Go forum that I follow regularly. The only version available was an online one, so I decided to create a physical game board, allowing it to be played in person. The rules can be found on this YouTube...

A tabletop gaming experience designed to fit perfectly on a 20x20 centimeter surface, ideal for playing at your fingertips whenever and wherever you want.

Ben Ben Version: 2015 Units: Millimeters Dimension: 5197.53 x 2103.98 x 1074.44 Polys: 58 569 XForm: Yes Model Parts: 5 Render: Corona Formats: 3Ds Max 2015, OBJ, FBX

Ben 10 3d model

Ben 10 3d-model

Customized version of https://www.thingiverse.com/thing:2006116 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2006116

Customized version of https://www.thingiverse.com/thing:4681765 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4681765

Customized version of https://www.thingiverse.com/thing:3045130 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3045130