belt loop molle adapter 3d models

The design has been revamped with a widened slot to accommodate a belt, and the rear section reinforced for added stability.

I'm showcasing my customized VOOPOO Drag 157 Mod adorned with a rugged belt buckle, featuring an adjustable top that can accommodate tanks of varying diameters up to 26mm for belts measuring up to 30mm in width. ...Enjoy your next printing project and...

... and NRL22. ...Remixed the mag holder and added a belt clip with a little extra standoff. Mag is snug but fits fine. Made to fit 1 1/2 inch belts. ... V2 I added a bottom so it didn't sit flush with the baseplate and added a couple drain holes.

Some nylon belts - such as mine, don't let you take it off the buckle so there was no way for me to slip it into the belt with it, so I cut a small 2mm gap to allow me to slip it in and out This is only the back, grab the other 2 parts on Mul13r's...

***HOW TO USE:*** Print this out, then slip those pesky belt leftovers into the closed-end clip. Use the open-end on-the-clip to keep your excess beltage securely in place where you need it most. ... _(You can also use this as a clever clip-on...

... ...Compact printing bed a concern? Other designs fall short, failing to secure cartridges or cluttering up with tiny parts? This single-piece clip securely holds 3 x 12g CO2 cartridges in place and allows them to be conveniently carried on your belt.

Rather than create a whole new belt clip/holster, I decided to cut off the silly carrying handle from the supplied locking holster, and created this belt clip. I epoxied it to the back of the holster. The handle of the x7 is completely hollow. I...

... ...The original fit was spot on, but I wanted more flexibility in my setup, so I added a simple belt attachment to make it easier to wear on the go. ...Big thanks to MJterry03 and cdamet23 for their outstanding contributions that made this possible!

To make this holster, you'll need to sew a piece of 25mm wide and 5mm thick belt material. Once you have it cut out, attach velcro tape to both the holster and the RX100 camera body. This will give you a secure fit. I used my AFINIA H480 printer to...

To create this holster, I started by sewing together a 25mm wide piece of durable belt material, precisely cut to 5mm thickness for optimal flexibility. Next, I carefully sewed or pasted velcro tape onto both sides of the holster and the RX100...

... female adapters. ...Key items include the MOLLE CLIP, P-Rail Adapter, Mini BIC, Shell Holder, Belt Loops, Mag Pouch AR15, and Hinge. Additionally, don't forget to explore other designs and follow daily KooKoo uploads for more great creations. ...Enjoy!

Disegned for standard Molle. Print in ASA,ABS or PETG.(The fit is pretty tight and i think PLA might break) Supports are only needed for the mounting clips. ...

For the tactical Phone Bag. ...To clip easy on your Pants or Belt.

Be patient when removing the internal supports from the belt clip - it can be a bit of a challenge, but take your time and use tools like a small chisel, wood screws, the knife on your OHT, or anything else you think will help. ... Print Settings:...

Remix of https://www.thingiverse.com/thing:4158517 by N3X15 I just widened that one to make it fit my wider 1.5in (38.1mm) belt.

Enhanced flexibility is now available by increasing the belt aperture to 45 millimeters, allowing for a broader range of applications. ...Printing can be performed using standard support structures throughout.

MOLLE CLIP: https://www.thingiverse.com/thing:2783462 P-Rail Adapter: https://www.thingiverse.com/thing:2784920 Mini BIC: https://www.thingiverse.com/thing:2781490 Shell Holder: https://www.thingiverse.com/thing:2784000 Belt Loops:...

... ...Both ends of the Dräger Dolphin loop hoses will fit onto this adapter. ... Most likely they will need to be printed with a brim to avoid detaching from the print surface, as the contact area is quite small.

... in this design. ...Both ends of the Dräger Dolphin loop hoses will fit onto this adapter. Most likely they will need to be printed with a brim to avoid detaching from the print surface, as the contact area is quite small. Category: Sport & Outdoors

These will fit onto the fan adaptor in [this design](https://www.printables.com/model/151420-loop-dryer). ...They will fit onto the rEvo loop hoses on the side that attaches to the unit.

These will fit onto the fan adaptor in [this design](https://www.printables.com/model/151420-loop-dryer). ...They will fit onto the KISS Sidewinder loop hoses on the side that attaches to the scrubber.

These will fit onto the fan adaptor in this design. ...They will fit onto the rEvo loop hoses on the side that attaches to the unit. Category: Sport & Outdoors

These will fit onto the fan adaptor in this design. ...They will fit onto the KISS Sidewinder loop hoses on the side that attaches to the scrubber. ... Category: Sport & Outdoors

These will fit onto the fan adaptor in [this design](https://www.printables.com/model/151420-loop-dryer). Each one will fit onto both hoses on the respective side of the unit, on the side of the hose that attaches to the T-piece (the right hand side...

... its belt slide. Attach to the MOLLE adapter, and you're in business! If you print this and try it out, please comment with how it works for you! ...I've considered making a v2 with MOLLE straps, but I'd like to hear how this works for folks first.

An adapter to attach to my belt sander.

The Belt Adapter V2 has been fully repaired.

Use this in combination with other MMS modules found on my profile to mount your items to the outside MollE loops on your bags, backpacks and vests! Works great with MMS Magpouches! ...Or you can get an MMS mount from my profile to mount your own...

I redesigned my original Gerber Strongarm molle adapter with a lower clip point, adding approximately 12mm to improve the center of gravity and clearance when seated or resting.

Yet Another MRH Accessory Converts Any P-Rail System to MOLLE Compatible in an Instant, with Male and Female Adapters at Your Fingertips.