behringer td3 stand 3d models

Double stand for Behringer TD-3 and RD-6 (they both has the same dimensions)

A rack that fits 2 behringer TD3's or RD6's. You might want to add m3 threaded rods and nuts to connect the right and left sides. The fit with the synths is ok. ...You can tune the frame with your TD3 for a nice snug fit because there is a small sizing...

A rack that fits 3 behringer TD3's or RD6's. You might want to add m3 threaded rods and nuts to connect the right and left sides. The fit with the synths is ok. You can tune the frame with your TD3 for a nice snug fit because there is a small sizing...

Stand for Behringer C-1U hub, with groove to pass the USB type B cable.

Simple stand for Behringer Xenyx 502 to prop it up Designed in Fusion 360

This is a simple [BEHRINGER UM2](https://takulog.info/BEHRINGER-UM2) stand which is one of simple audio interface. I made this PVB filament for the gross of this picture, but it can be made by PLA, and so on. ... ---- [ベリンガー...

Set of synthesizer module stands for the Behringer Crave module. ...Simply replace the existing end caps (2 screws on each side) with the newly printed stands

I designed and printed this custom vertical stand specifically to house my Behringer UMC404HD, freeing up valuable desk space that was previously consumed by its bulky footprint.

Simple stand for the small Behringer 502 mixer. You'll need 4 screws M4 x 15 to mount the frames. ... The frames have a close fitting, this is part of the design :)

I needed to see better on these little micro devices from behringer so I have designed a stand for them which just slides on and hold itself to it. It fits every Micro device from the Behringer line up. It is a 30degree stand so the viewing angle is...

I helped my buddy out by building a custom stand for his Behringer XENYX 1202 Mixer. To fit, this stand needs to be just under 9 1/2 inches wide inside. ...If you're not seeing the pictures right, try viewing the original post to get a clear view of it.

... a synth underneath/in front of my k-2. I'm assuming this will work with most behringer synths as they all seem to have the same side panels? ...Getting a wasp soon, will check and update, or if anyone knows for sure feel free to comment :) thanks

This is a simple BEHRINGER UM2 stand which is one of simple audio interface. I made this PVB filament for the gross of this picture, but it can be made by PLA, and so on. ... ベリンガー UM2 向けのスタンドを製作してみました。ポイントは、XLRケーブルを後ろに回せる真ん中の穴で、デスクが散らかりにくくなっています。 ...

This is an elevated stand I made for my Behringer X-Touch so that it was a little more ergonomic and allowed me to read the scribble strips a bit better. It's split into two pieces so that it can print on something like and Ender3. ...I personally added...

A simple stand for the Behringer Crave that positions the synth in an 45° angle. Simply print 1 or 2 of them and put them underneath the synth. They are snug fit so I did not constructed a traverser to keep them in a fixed position relativ to each...

This is a table top stand for the behringer mixer series the space between the "hooks" is 26mm so if your mixer is the same or thinner, it will fit. the connections are friction fit, so you have to use a tool to press them together. ... see picture

I'm a big fan of the Behringer Model D stand. It's simplicity is what makes it so effective. Feel free to modify it if you want, but it works perfectly for me. Thanks for sharing! ...Have a blast making music with it!

I created this so my Behringer MX602A stand on top of my modular synth case and have good access to the controls. It uses the same screws that hold on the original side plates. Printed fine for me without supports. ... Made in Fusion 360.

So here's a stand for the Behringer BCR2000 rotary MIDI controller and the BCF2000 Fader controller as well. I built this stand to clear some space on my desk and get a better view of the knobs. Maybe it'll be helpful for you too. You'll need to...

The Behringer audio mixer should be positioned at an incline on the desk, allowing for a more comfortable viewing experience while seated.

A set of legs for the Behringer Model D synth, inspired by this design: https://www.thingiverse.com/thing:5340392 I printed in PLA+ at 40% infill and found it printed very well.

The technical specifications can be found on the Music Group website: http://www.music-group.com/Categories/Behringer/Signal-Processors/In-Ear-Monitor-Systems/P16-M/p/P0421 To assemble this bracket, you'll need two M6x40 screws, one M6x50 screw, and...

This is what happens when Behringer makes a module that draws WAAAAAAAAAAAAY too much power to be included alongside other eutorack modules. ... You might print a bit thicker than provided - i've noticed that the brackets work but don't feel as...

Mic stand adapter for the B105d & B205d speakers.

It´s a support stand to raise what you like :)

I created a stand for the Xenyx Q502USB. There are two screws on the back of the mixer. Measure the height and distrance. After that drill some 2-2,5mm holes in the stand. ... Fix with screws (maybe need longer ones), done :)

... play with any settings. So I made a stand for it! Remove the 4 black screws at the back and replace the top two with M3x8mm screws instead. ... The pictures show an earlier version which had 4 screws, but I found it wasn't needed and removed them.

A table stand for my mixer. this way I can see all the controls at a glance and from a distance.</p><p>you can loop the cables under the beam to keep it a bit tidy.</p><p>Use some force to clamp the parts together. ...It's a tight fit.</p>

So I built a stand for it! Remove the four black screws at the back and replace the top two with M3x8mm screws instead. The pictures show an earlier version that had four screws, but I found out it wasn't necessary and removed them. ...Print Settings...

Then I printed the stand here https://www.thingiverse.com/thing:2038119 However I didn't have a good matching set of hardware to fit snuggly against the frame. So I decided to model a version which fits into the side clips! It provides enough...