beehive 3d print

A handmade two-piece wristlet designed using the open-source CAD software found at openscad.org - still a work in progress, crafted by an amateur with much to learn.

Spare replacement pegs for Technoset Queen Castle Beehive

This design provides an alternative for those with access to a 3D printer.The spacers are designed for 37mm frame spacing, although the individual spacers allow this to be varied.These spacers have yet to be tested in a real beehive.This file...

adaptable door for nicot holder, for dadant hive. ... adaptable holder for nicot holder, for dadant beehive.

... mount the Beehive to a metal wall/door/case etc. ...Just insert the magnets during the print process. I printed the wallbase at 103% for a perfect fit of the magnets.  All credits to https://www.prusaprinters.org/social/2940-rodrigo-menendez

An additional entrance for Abelo beehives useful when doing a Demaree split or just as additional entrance for the bees during peak flow. ...take the polystyrene plug out and pop it in.

Designed to fit a Harvest Lane beehive prybar, may or not fit other brands. your printer tolerances will change how tight this holds the prybar. ...If the fit is too tight, file the hole, or reprint with 2 or 3% scale up.

Introducing an innovative version of the Dadant-Blatt 10 frame beehive (M BD 10). A key feature is its extended top frame bar length of 480mm, typically observed in Langstroth-Ruth hives. ...This design enables users to employ Langstroth frames, albeit...

... were designed using TinkerCAD, and SVG templates were created specifically for the screws. ...This project was initiated during the 2018 EM Lyon Makers'Lab Bootcamp #6 with the objective of crafting a protective case for a connected beehive system.

This is a specialized guard for LR beehives. Simply attach it to the hive using two convenient holders and then slide it into place. ...If you insert it from left to right, you can use 8mm holes, but if you insert it from right to left, the entrance...

Upon request here some really simple beehive frame spacers. They come in 4 flavors (and you can easily scale them e.g. in Cura to any size in between/beyond): - 6 mm - 8 mm - 10 mm - 12 mm Use small (15-25 mm) nails to mount to the sides...

It is inserted between the entrance gate and the beehive. By using the handlebar, you can move it left or right to change the number of entrance holes. No additional assembly steps are necessary. 2 sliders: fully closed or 1 hole open, approximately...

Hello. ...A clip-on extension plank no longer needs screwing. It prints well on this material over time. ...30% fill density, 2000 micron layer thickness.

Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Yes Supports: No Resolution: .15 Infill: 100% Filament: eSun PLA+ White Notes: 100% infill is probably not required but it is only ~10g per strip even at 100%. I printed these with 4 walls...

... typical PLA+ settings anyways. I printed with a small brim just to stabilize it a bit. Print to your preferred material and settings but I do suggest .15-.20 resolution otherwise the cells get a little wonky. ...</p></div></p></p></p> Category: DIY

Simplifications are as follows: - Queen excluder: horizontal rails on queen excluder would be too thin, only showing representation on model - Simplified frames have no small rebates - hive tool is 5mm thick full-scale (actual is 3mm), so that it...

... cells are on both sides of the strip. The extra thickness allows these to be printed standing up. These slipped snugly into langstroth frame tops from Mann Lake. ...I will be using these as frame inserts in swarm traps to capture potential swarms.

5 cookie cutters with bees, honey, honeycomb and beehive design, 7 cm or so. Exclusive cutters of La Tuerca 3D. Firm, robust, but at the same time economical models. ...Print with good filament.

Model that fits perfectly to the extension of the take-off board for nicot hive flooring. All you need is a few dots of glue (cyanolite) and a chicken wire. ... Coupled with a few traps, it's quite effective.

Simply poke small holes in the top of your mason jar, fill it with sugar water, and place it on this beehive feeder. This feeder will fit any quart-sized mason jar with a 2.75 inch outer diameter lid perfectly. ...I designed this object to print...

Four beehive levelers are required per beehive, five if using a liquid other than water. Three printed components are needed for each Bee Hive Leveler. The Nut Turner Guide prevents the nut turner from slipping under the hive. The Nut Turner turns a...

Easier Ice Removal Made Easy with the Advanced Beehive Ice Tray - Featuring Rigid and Soft Molds with No Supports Necessary.

Spacer for moving from a straight frame to a hoffman frame works for beehive frame and mini plus frame

A beehive in the cubical style for your keychain . Its dimensions are : X: 20.0 mm. Y: 20.0 mm. Z: 42.1 mm. It is ready to print. I am sure of that and check it in blender. It has : Non-Manifold :0 Intersections :0 zero faces and edges: 0 non_flat...

Nesting blocks for housing red and horned mason bees comprise 11 nesting holes (8mm diameter). These holes are held together by lashings. Ensure these nesting blocks are sheltered from rain. Nesting blocks provide easy monitoring of bees; in autumn,...

Cookie Cutter / Fondant Cutter ( 9cm cut-out size) For Personal Use Only

Model includes stand, bottom board, deep brood box, brood box, super, crown board and roof.