bed level test print ender 3 3d models

Each side will hold a maximum of about 400 pages, making an up-to-800-page book when printed double-sided. I use this jig to bind both my PDFs and compilations of my children's artwork into neat archives for later enjoyment. We've probably compiled...

I use this as a wireless monitor for framing a shot. But there are some killer features of a DSLR I wanted to have on my phone when filming. So I made this Camera Rig and I slip my iPhone into on days I'm filming.  Print...

Print and assemble a few battery cases and sell or give them away to put them to good use once more.. Ok so a short build go-through... I took old defect/dead Ni-Cd/Mh packs Cut them open at the bottom Pulled the old cells and flex out. Took some...

This was a substantial enterprise that involved making the spheres, printing the gores, building sturdy stands, packing, and distributing them across Europe. Mercator was also renowned for his scientific instruments, particularly his astrolabes and...

If you mount it on the back side, it will give you a little more room for your foam/rubber to compress and give you more pedal movement and you only need to print the back side mount. Naturally then, if you mount it on the front side, you can screw...

Parts * Paperclip * M2 screw/washer/nut * Elastic * 3D Printed Components This models are pretty simple, I'm sure you'll be successful with whatever you have on hand although I'd like to give it a go with something along the lines of TPU one day, I...

It prints quickly, uses only about 1 gram of filament (0.33 metres of 1.75 mm filament), and is very easy to use.It clips onto the spool of any brand of filament, so it's a universal clip. It can clip onto 1.75 mm filament or 2.85 mm filament, so...

From this students can derive the pulley constraint equation (https://ocw.mit.edu/courses/physics/8-01sc-classical-mechanics-fall-2016/readings/MIT8_01F16_example8.9.pdf).  Using the constraint equation, the basket can be attached to the double...

The robot has been fully printed with open-source 3D printers, uses open-source hardware, and was designed entirely on FreeCad. This robot is inspired by the MTRAN III, developed by The National Institute of Advanced Industrial Science and...

Simply remove the filament from your extruder, turn down the heat and clip on the laser diode.----------------->To create the tool paths follow this example of cutting a square:<--------------a) Creat a 3d model of a square that is the same...

Note: I actually haven't printed any of these. I'm a designer for Shapeways here: https://www.shapeways.com/designer/jonathanmarch/hire-me. How I Designed This The Work First, I found a font that I could use for anything that also connected most...

#Whistles I also tried to print some whistles, with some examples here, but none of them make so much as a peep. Please feel free to discover where I'm going wrong! ... #Photos I've uploaded an album of photos and videos of this project here:...

The provided code appears to be a G-code script used in 3D printing for generating the patterns of case cutters, specifically for a case design related to phone designs (based on some keywords). It specifies a series of dimensions and positions...

STL is ideal for printing objects due to its simplified 3D geometry specification and direct data importability from computer-aided design programs. DXF (drawing exchange format) files allow conversion into DXF drawings that contain the same...

after you get the fitment and angles right i suggest printing an "all finger base blank" which is in the files. you will need to know the angles and the the distances, but it will allow you to make your overall device more stable and with no chance...

This set includes: - 1 Highly Detailed Snakewoman Archer A (no base)- 1 Highly Detailed Snakewoman Archer A (covered) (no base) - 1 Highly Detailed Snakewoman Archer B (no base)- 1 Highly Detailed Snakewoman Archer B (covered) (no base) - 1 Highly...

Steps: - Print the file - Slide the PTFE into its location at the desired length - Use a felt tip pen to mark the start of the contact on the tube - Take out the tube and cut it round on the outline as on the attached renderings - Replace the tube -...

If the 3D print didn't come out well, a knife or awl can be used to punch/ream a hole in the bottom. Insert the LED leads into the shade and glue the LED firmly into place using super glue.\n Cut out a 10x26mm rectangle of the reflector material and...

Julia's Coffee Table Lucas Newman George Mason University - Math 401 - Mathematics Through 3D Printing October 25, 2021 This math art object is a blueprint for a coffee table with a beautiful, branching, fractal tabletop. It's certainly an odd...

The lid mates nicely to the case, but doesn't really lock in place enough that I was comfortable swinging it around with electronics inside, so I welded the lid to the case with a 3D printing pen. You could use glue or whatever. There's no way to...

Using electrical systems, sensors, and modern FDM 3D printing capabilities, the team’s revolutionary design to what seems to be a simple design challenge at first glance, performs optimally. The design uses a gyroscope and accelerometer sensor that...

You need to 3D print two of the 4 inch bulkhead fittings and one carbon canister adapter, or figure out your own way of getting the vent hoses into and out of the fume scrubber. I used 4 inch dust extractor hoses, made for woodworking. The inside...

Intended for 3d print. Tank turret for the early WW2 era, gargantuan 12 man crew French Char 2C tank. The model kit includes two turret variants:   Main turret decorated with the coat of arms of Normandy (this is actually historically accurate -...

... As an option, the NEMA17 motor strapping allows to fix a motor with two 3mm diameter screws. Note: The instruction mentions that some parts are designed to be printed without material support, and that the device has been modeled with Fusion 360.

A single support (base + 2 side panels) and a nut can be printed for each spool and the spool would only be changed by releasing the wing nuts so the spool screw would not have to be removed. It'll need: -2 bearings 628 / 6-2Z (13x6x5)mm -100mm...

You may also request this model printed and assembled with velcro at https://jkl-adapters.com/   Description To solve the tracking issues experienced by penholders while playing Eleven Table Tennis on the Oculus Quest 2, I created a series of penhold...

SCALE: 32 mm   DESCRIPTION:   This miniature comes pre-supported and un-supported in STL formats for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. This figure has...

Finished in 1992, the building rises to a height of 668 ft (204 m) with around 944,000 square feet (87,700 m2) of interior space. The building, with 51 floors, was designed by Ricardo Bofill. It was formerly known as the RR Donnelley Building when...

Take a look at my hinged cable organizer to manage those pesky cables as well: https://www.thingiverse.com/thing:4640618 Copy and customize it on Onshape:...

All parts are printed in Overture pink PETG. Cleaning remains to be seen if it will be a problem, but hasn't been too bad so far. Most hardware is M3 and a few M4. Rods were threaded to #8-32. I can provide drawings for lathe parts if requested. ... ...