bed for three bl 3d models

I made this BL Touch mount is because there is no suitable mounting for the Ender 3 Max printer. You will need 2 x M3 Bolts and 4 x M3 Nuts, the two extra M3 nuts replace the spring that comes with the BLtouch to enhance the stability and accuracy...

A custom battery holder designed specifically for the miniature "Blade MCPX BL" radio control helicopter. The compact white holder serves as the standard component, while the vibrant orange holder has been freshly printed to meet the exact needs of...

This is actually an extension rather than a remix, and it's specifically designed to work with the BL-Touch probe that's aligned directly with the hot end. ...The offset values for this setup are 53 millimeters in the X-axis and 0 millimeters in the...

... BL Touch sensor in place. ...These brackets were designed specifically for use with the Greg's/Wade Extruder, yet they can be adapted anywhere else. ...The rear mounting bracket is deliberately offset to accommodate hot end cables situated at the back.

The original file does not include a mounting bracket for the BL-touch probe; therefore, I created an alternative to facilitate assembly. ...It is recommended that you print this component using ABS material, but PEGT and PLA also produce satisfactory...

I wanted to add a BL Touch to my Sparkcube, so I printet this Model: https://www.thingiverse.com/thing:2629302 But that did not work because it was not for the modified xcarriage I am using: https://www.thingiverse.com/thing:349186 So I designed a...

The optimal choice featuring a BL-touch allows seamless printing using a 3D printer.

... as close as you can get it. i hope this made your Bl touch easier to mount and work. you will still have to change the eeprom>motion>babystep z> 0.000 to -0.59 (negative) (then save settings) or something still, depending on bed surface, i imagine.

This is a simple spacer based on the CR-Touch bed leveler but will also work with a BL-Touch. Issue I was having was with changing extruders and nozzles and ending up with the probes being too high thus causing my nozzle to ram into the bed. With...

This is a mount for a BL Touch on an A8 Plus. I had found a number of alternative methods, but all looked a little flimsy with a large cantilever. This is Easy to print Easy to mount Strong Integrated cable management I have produced two versions:...

I recently changed to a Titan Aero, but wanted a bracket for my BL Touch, but I could not find any stand alone brackets so opted to design one, this mounts off the fan, and puts the BL Touch in line with the nozzle and 41mm in front. I designed mine...

I was in dire need of a BL Touch mount for my Anycubic Kossel that wouldn't collide with the rods and would only cover the upper half of the 40 mm hotend fan. After some careful consideration, I decided to design one myself. ...The resulting mount is...

I want to install a Cobra fanduct on my AM8 with E3DV6 and I'm having trouble putting the BL TOUCH sensor in at the same time, so I designed a support for my BL TOUCH sensor to go behind the print head. The mount attaches directly to the aluminum...

... of the sensor to the printer itself. Two screw holes from the fan mount are utilized for this purpose, and double-sided tape is also applied to ensure a secure fit that resists movement. ...If a superior version exists, please share it with me.

I get fed up of having to reset the Z offset each time i remove the fan shroud for cleaning/maintenance etc so i cut off the lugs that share the same screws so the BL Touch stays mounted when the fans are removed. ... The M5 bolt that sticks through the...

I get fed up of having to reset the Z offset each time i remove the fan shroud for cleaning/maintenance etc so i cut off the lugs that share the same screws so the BL Touch stays mounted when the fans are removed. ... The M5 bolt that sticks through...

This is a custom mount designed specifically for the BL-Touch on the JG Aurora A5 3D printer. It's been expertly integrated with a cooler enclosure to enhance performance and stability. When installing, be sure to replace the original screws with...

For the air channels you have to work with support blockers, otherwise you are unlucky and the ducts are closed.... I have worked with Cura with anti-warping tabs what has worked very well for ASA... Attached are the pictures of the tested...

i edit the level sensor holder so that the layout hole layout fit to the original BL Touch

I've crafted a custom mount specifically designed to attach the BL Touch precisely where the original sensor was situated.

This is to prevent the Astrolux BL-06 to turn on whilst in pocket (the keys are very sensitive).

none of the mounts that come with the BL Touch fit this direct drive set up so I made this to fit it the 2 drilled and tapped holes need smaller screws than what comes with the BL Touch but the 2 holes are ones that are cut out by the 2 screws that...

I've always struggled with getting my BL touch dialled in precisely, so I sought out a solution that could be adjusted from the top with just one turn of the screw. Either a spring over the M4 screw and printing a dial for the top would work, or...

I wanted to add a BL Touch to my Sparkcube, so I printet this Model:https://www.printables.com/model/173295-sparkcube-filament-fan-holder-railBut that did not work because it was not for the modified xcarriage I am...

You could use either a spring over the M4 screw and print a dial for the top, or use elastic bands as I have to keep the tension. Update I no longer use this thing since learning how to properly set z height offset, and Ive since updated the print...

Battery Holder for a smal "Blade MCPX BL" RC helicopter. The white holder is the original holder, the orange the newly printed Battery size maximum 17.2x11.7mm Print Settings Printer: A6 Evolution Cube Rafts: Doesn't MatterSupports: Yes Resolution:...

The mount is precision-designed with all specified mounting dimensions incorporated, eliminating the need for shims or sanding to achieve optimal height. To ensure accuracy, I recommend slowing down your print speed and utilizing the best resolution...

I downloaded Teaching Tech's backplate for the BL Touch but after printing and installing I found that the X Axis limit switch was not engaging. I went about changing the limit switch cover but with testing I had found that it was the actual plate...

I downloaded Teaching Tech's backplate for the BL Touch but after printing and installing I found that the X Axis limit switch was not engaging. I went about changing the limit switch cover but with testing I had found that it was the actual...

... with a 40mm fan and a BL touch mount. ...The part where the BL touch attaches shows some minor damage, yet it continues to print flawlessly and exhibits impressive strength. ...It's currently installed on my printer, performing exceptionally well!