bcs trophy 3d models
8581 3d models found related to bcs trophy.
cults3d
An approximate model of the old college football BCS trophy / the current Coaches' Trophy. The model is true-to-life sized at 34" tall for the entire trophy, while the crystal football itself is 12" long. MAJOR NOTE: My 3D printer is out of...
prusaprinters
An approximate model of the old college football BCS trophy / the current Coaches' Trophy. The model is true-to-life sized at 34" tall for the entire trophy, while the crystal football itself is 12" long.MAJOR NOTE: My 3D printer is out of...
thingiverse
An exact replica of the vintage college football BCS trophy / the modern Coaches' Trophy has been designed. The model is precisely true-to-life sized at 34" tall from base to tip, while the crystal football itself measures a full 12" in length. If...
thingiverse
Showcasing the BCS stage, designed creatively by Eoghan and crafted using the powerful 3D modeling tool, 3DTin. This impressive virtual creation demonstrates Eoghan's artistic talent and his ability to bring designs to life in a digital space. ...Be...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following settings: message = BCS stick width = 8 mm font thickness = 5 units font size = 10 points stick thickness = 3 units hole radius = 3 units flat bottom = 1...
grabcad
The 3-lobe BCS transmission features a Bertolini threaded compass-shaped guide (20x17 with 12 cavities).
thingiverse
... mit der Oberseite von oben nach unten in den Halter einschieben. Remixes welcome. Fast, lightweight wall bracket for the BOSCH BCS 230. Because the charging cable is relatively short, slide the charger upside down into the holder. ...
thingiverse
Formation cards for the Battalion Combat Series (BCS) games by Multi-Man Publishing (MMP). Pick the size formation card depending on the game. Arracourt uses 5/8 inch counters. ... The rest are 1/2 inch.
cults3d
Formation cards for the Battalion Combat Series (BCS) games by Multi-Man Publishing (MMP). Pick the size formation card depending on the game. Arracourt uses 5/8 inch counters. ... The rest are 1/2 inch.
thingiverse
... ... **Instructions** Use the given options to create: • What: Number Three • Font Percentage: Seventy-Five Percent • Outer Width: Five Units • Font Width: Two Point Zero • Clip Width: Twenty Units • String One: BCS
grabcad
A IKO linear guideway / guiderail that I scrapped from a machine.IKO LWL9 BCS with a 240mm rail.IKO is a very high quality bearing manufacturer from Japan.These rails have almost no play and would be very good for 3D printers for example!Model drawn...
grabcad
A IKO linear guideway / guiderail that I scrapped from a machine.IKO LWL9 BCS with a 240mm rail.IKO is a very high quality bearing manufacturer from Japan.These rails have almost no play and would be very good for 3D printers for example!Model drawn...
thingiverse
Here are the key takeaways for a successful print: Always print with supports for optimal results, especially when printing with small layers. ...Printing upright without supports can also yield great results, provided you have sufficient brim to...
thingiverse
Customized version of https://www.thingiverse.com/thing:3045130 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3045130
thingiverse
Customized version of https://www.thingiverse.com/thing:3045130 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3045130
thingiverse
Customized version of https://www.thingiverse.com/thing:3045130 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3045130
thingiverse
Morphi Design This model was created with Morphi! http://www.morphiapp.com. Morphi empowers people of all skill levels to design 3D printable models on the go using intuitive touch controls, eliminating the need for wifi or a mouse. Get the app now...
thingiverse
Created with Customizer! ... Customized version of http://www.thingiverse.com/thing:74322 Instructions Using the following options: pane_size = large picture_shape = standard picture_orientation = vertical...
grabcad
Featuring a 106mm spacer bar, this item is designed for Bertolini tools on one side with a 70mm centering and has a 100mm hole on the other side for a BCS cultivator with a 60mm centering.