battery cover for roku remote 3d models

I discovered three potential replacements for a Roku 3 remote battery cover: https://www.thingiverse.com/thing:1525091, https://www.thingiverse.com/thing:2246134, and https://www.thingiverse.com/thing:1914364. They all claim to fit the Roku 3...

The original did not fit my remote was 3mm too short. ...I remixed the original to fit my remote. The side walls seem too thin, need to increase the side thickness. But works for my remote

This replacement battery cover is specifically designed for use with the ROKU 3 and ROKU ULTRA remotes, offering a snug fit that ensures optimal performance. Please note that you may need to perform some minor trimming (dependent on your printer and...

The small tab snapped off my Roku remote about two years ago, leaving me with a broken device that's been held together by tape since then. This makeshift repair has always resulted in a sticky mess on the back of the remote. I suppose you could buy...

This was created for myself out of necessity. I didn't check to see if anyone else had created one before I did it myself so I probably could have saved myself an hour of work but oh well. ...It works perfectly and seems to be slightly different than...

This is a replacement battery cover for a Roku remote for TCL TVs. I made this because I hate searching for the remote, and I didn't want to buy a new one that does allow tracking. As a side benefit, the extra length makes it easier to grip the...

A battery cover for a TCL branded roku remote.

This is a functional accessory that secures the batteries within a Roku Premiere+ remote's housing. Although it doesn't reach the full extent of the remote, its design accommodates the double curve by using strategic cutouts and recesses. ...The tabs on...

... other with a button to release the battery cover. If this sounds familiar, use this model. If your Roku remote doesn't have a button to release the battery cover, try my other Roku battery cover at thingiverse.com/thing:2246134 Have fun printing!

This is a replacement battery cover for a TCL Roku TV remote. There are several versions of Roku TV remote, so this may not fit yours. The STEP file was included in case you'd like to adjust it to fit yours. The Airtag cover is still not perfect. ...

I tried so many downloaded roku remote battery covers, there must be many versions.Printed it in PETG at 0.2mm, the "I made this" on the back might be nicer with a smaller nozzle and/or lower layers, but this was my second revision and I wanted it in...

It takes one AirTag, "white side" out because the white surface seems to be the resonator for the speaker (putting it in the other way makes the "play sound" feature much less useful) I printed this with supports "open side down" so that the mating...

Here's a custom-fitted battery cover for my Roku Ultra remote. I designed and printed a few other covers earlier, but none of them came close to fitting perfectly. To get it just right, I took precise measurements and created a model that matches my...

Replacement for Lost or Broken Roku Stick Remote Battery Cover. ... I Found an Alternative to the Standard Covers, But None Seemed to Fit Properly, So I Took Matters into My Own Hands and Designed a Custom Solution That I'm Happy to Share with You.

A battery cover for a TCL branded Roku remote. This is a remix of thing:4723299, with thickened walls for improved printability. The thickened walls-shape also provides a wobble-free base when placing the remote on a table. ... Based on the previous...

Replacement battery cover for the TCL Roku RC-AL5 remote control. This model appears to be dimensionally accurate but is a very difficult print. It requires supports at any orientation.</p><p>If you have a successful print and fit, please let me know...

Battery Cover Replacement for the Roku 3 Remote Control Model 4200X - Compatible with Other Models

I was tired of the battery cover coming off and didn't want to just tape it. ... Print upside down with support, I used tree support in Cura.

The modified tab is now shaped and sized differently, while the support piece connecting it to the remote cover's body is thicker and flush with the top of the battery cover.\r\n\r\nI suspect that for most Roku remotes with a bulkier design, either...

This replacement battery cover is specifically designed for the Roku 4 remote control. Initially, a small tab on my original cover broke off, prompting me to create a revised version with a new tab. However, I discovered that removing the tab...

Basic, printer-friendly battery door for the Roku remote. Fits pretty nicely, but has a flat bottom to help print easily. Recommend a small support under the clip portion. ... Print Settings Printer: Flashforge Finder Rafts: ...

This battery cover fit perfectly, but the clip did not catch. I redesigned the hook and it is working properly. I've attached the Fusion 360 file in case you want to redesign. ... This is a remix from https://www.thingiverse.com/thing:2696333

This is a custom cover for your remote control. The original design had some issues that caused it to break after one accidental drop, so I decided to create a new cover instead of purchasing another remote. Since injection-molded parts like this...

Battery cover for Samsung TV remote. ...I don't remember exact remote or tv model, but it was LCD/LED tv.

I need a brand-new battery cover for my trusty old Sharp television remote control. ...It's going to take some reinforcements to get it working properly again.

The concept can be adapted to any remote control, but these custom brackets were specifically designed for the popular Roku 3 remote, which is often used in my household without the need for manual support. ...I envisioned that individuals with limited...

&nbsp; Now find your roku remote with an airtag!!! &nbsp;It is also a quick print. &nbsp;Use my settings and it will be done in 3 hours (petg)! ...&nbsp;</p><p>&nbsp;</p><p>Print Settings:</p><ol><li>Supports</li><li>15% infill</li><li>recommend...

Want to save your marriage? ...Here is a roky remote holder with AirTag slot. ... Print Settings: - Supports - 15% Infill - I recommend PETG

Fischertechnik Remote Control Battery Cover.

Battery cover for Thompson / TCL TV remote RC3000E02.