bathroom sink strainer 3d models
32243 3d models found related to bathroom sink strainer.cults3d
It fits our bathroom sink drains. Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=351541 The slots are intentionally narrow to capture small stuff. To test it fully open the faucet and make sure that the water do...
thingiverse
It fits our bathroom sink drains. Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=351541 The slots are intentionally narrow to capture small stuff. To test it fully open the faucet and make sure that the water...
prusaprinters
Perhaps you are the kind of person who has a bathroom sink where the plunger stopper failed one day and the only way to fix it was to replace all the parts.Perhaps you removed the plunger so you could keep using the sink and said “I'll fix that one...
thingiverse
But only time will tell if it can spin smoothly under water...\n\n \n \n Operating Manual\nBefore putting your new strainer to use, make sure to adjust its size to perfectly fit your sink. ...Keep in mind that printing with raft support is a necessity...
pinshape
Our sink no longer had the metal tabs to hold a typical strainer up so I created this one to lip over the drain on the sink. It uses a 30 mm diameter and 10 mm height for the base portion. The holes are tiny so it does slow down the water some while...
thingiverse
Bathroom sink plug hole filter to fit 38mm hole. Can be printed without supports, Loved the original design by X1Project. However, due to the way it sat on our sink, water flow was really slow. Modifications done: - Connected the two top...
thingiverse
Drain is too narrow for comercially-available strainers. ...29mm diameter drain.
thingiverse
Basically this design was in response to my niece and nephew dropping water balloons down the sink and plugging our pipes. It was made to fit in even old sinks (basically ours no longer had the metal tabs to help). ...The base is 30 mm diameter and 10...
thingiverse
The lever to raise my drain stopper broke and I made this to keep things from falling into the drain until I fixed it. ...Don't know if there are a lot of bathroom drain sizes but mine measures about 30mm and this fits into that.
thingiverse
This sink strainer is a remix of the one designed by gratefulfrog because holes were too and it was collapsed too easy. Its size is the same as the remixed one: - Depth 10 mm - Interior diameter 40 mm at base. This sink strainer is made for...
thingiverse
Have been using a design from Zapta here on Thingiverse ( https://www.thingiverse.com/thing:2663141 ) which has been working great, but the cone shape is a little tough to clean out. ...Used some of the ideas I liked from that design to create my own...
thingiverse
Customized version of http://www.thingiverse.com/thing:351541 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=351541 Instructions Using the following options:...
cults3d
This is a simple sink strainer for your bathroom sink to prevent hair flowing into sink pipe and clogging. Unlike other sink strainers, you do not need to remove sink stopper. You just need to simply clamp it onto the sink stopper and the strainer...
thingiverse
I created a filter for the bathroom sink. Protects against hair and clogging. ... Dimensions: 12mm shaft 36.6mm tube spring loaded (work with most sinks) 100% infil no supports print time 20 min 2 slower layers (the print has a lot of holes) printed on...
thingiverse
Purpose – A Custom bathroom sink strainer, tuned for 3D printing. Design - Inspired by the symmetry of nature and flowers. Scalable – Default 51mm Outer Diameter, 28mm Tube Diameter (Sink Hole > 28mm / 1-1/8” hole diameter.) Un-check symmetrical...
thingiverse
Customized version of http://www.thingiverse.com/thing:351541 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=351541 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:351541 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=351541 Instructions Using the following options:...
thingiverse
A sink strainer designed for my bathroom sink. (20% infill, 0.12mm detail) Customized version of https://www.thingiverse.com/thing:3797754 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3797754
thingiverse
Design for a bathroom sink with diameter of 1.25", but works on 1.5" as well.
thingiverse
Print with any filament I printed mine with PETG. ...Stringing can be seen in the pic but useful nonetheless Maybe you have better printer/settings using better material. Can be used in bathroom sink for straining hairs etc.
cults3d
This is a simple sink strainer for your bathroom sink to prevent hair flowing into sink pipe and clogging. Unlike other sink strainers, you do not need to remove sink stopper. You just need to simply clamp it onto the sink stopper and the strainer...
thingiverse
Lever for stopper broke so made this quick to keep items from falling in the drain. ...I don't know if there are a lot of different drain sizes out there but mine was about 30mm and that's what this is made to fit.
thingiverse
Customized version of https://www.thingiverse.com/thing:3797754 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3797754
thingiverse
This is a two-part design, you need to glue parts together with any kind glue. ...
thingiverse
Customized version of https://www.thingiverse.com/thing:3176960 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3176960
thingiverse
Customized version of https://www.thingiverse.com/thing:3797754 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3797754
thingiverse
Customized version of https://www.thingiverse.com/thing:3797754 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3797754
thingiverse
To prevent future problems I created this hair strainer to fit in our bathroom sinks. It can't seal the sink but we never used that feature anyway. ...I tried to find the right balance between sufficient water flow and small enough drain holes to catch...