batgirl 3d

&nbsp;You can see in the pictures where I repaired these with a 3d pen. &nbsp;If you have an enclosure, that might help.</p><p>All the prints are done with PETG for strength.</p><h4>Print list with details</h4><ul><li>Brown...

... <font size="+1">^Like</font> button** and turn that heart red <img src="https://cdn.thingiverse.com/site/assets/like-button-liked.svg">.                                                      

... <font size="+1">^Like</font> button** and turn that heart red <img src="https://cdn.thingiverse.com/site/assets/like-button-liked.svg">.                                                          

- 3D Printing is about beauty and design. When storing the filaments visibly, the storage should at least satisfy some degree of beauty. When designing parts to be printed, you also need to take care of the print process: - The print...

The remaining Yeallow (G32, SDA) and white (G33, SCL) cables were soldered to the corresponding pins on the PCD, to connect them to the sensor module...

The tray should now slide into place.Installing Drawers/Trays under each other• This is the same process as above but instead of mounting the "Rail Lock" into the nut on the rail you will need to slide a “Rail Lock Upper” into place on the back of...

Theres is 9 parts printed in 3D, all in PLA. Thank's to HaikuFPV for the inspiration (https://www.thingiverse.com/thing:1410967). Try to use Tough PLA, like APLA+ if you can. ABS and other "hard" materials will work as well. Supports are...

... loading filament on each lane to test if the chamfers cut on the smaller tubing is enough to prevent the filament from getting stuck, and to see if the small tubing is seated correctly. Rechamfer/reseat as required Category: 3D Printer Accessories

The Gryphon is a mostly 3D printable, hobby-grade, Nerf semi-automatic flywheel blaster. Its main design features are as follows:Uses 130 to 180 sized 20.4mm , brushed DC motors.Semi-auto by rack and pinion with 1:3 gear multiplication. The trigger...

If you want detailed instructions with pictures, please see my instructable on http://www.instructables.com/id/The-Bicycle-Bubble-Machine/ Apart from printed parts, you will need: a piece of wood to mount the machine on, which will then be put onto...

No short circuits between the V G and/or S wires. Hardware I used these end-stops: https://aliexpress.com/item/32959048821.html I am not affiliated with AliExpress nor TwoTrees and there are LOADS of identical/rebranded switches out there. You will...

In my experience the sports ball inflation needle runs cooler - but wears out quicker and is more likely to deflect in use and cost accuracy. Because the guide can get warm from the friction of the needle running inside of it it's best to use a heat...

(Support on the build plate only.)Scale's easily if you want a larger or smaller version.Currently set at 75% size to reduce build time. Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun...

You can cut the circle that's sandwich between the two 3D printed pieces with good scissors. The holes for the crews and the tube are harder to make. Be careful, this mesh is sharp and you can get cut. I'M SERIOUS. I managed to make the screw holes...

Dragon and Mosquito use the same length of PTFE tube which is why they share jig.BOM - Bill of MaterialsI buy most of my 3D printer parts from quality stores on AliExpress. Shipping takes a while from China but quality is excellent and the prices are...

My bot came with 410 mm Y rods, which is reflected in the Blender file, but this design should work on older printers with shorter rods (the original i3 had 330-335 mm Y rods). The .blend file depends on my standard parts/materials library, which can...

See “Large Binder Clip Tentacle Monster” below in connectors.Tentacle Rail Clip BaseThis Tentacle System base includes a clip that attaches to the T-Slots in the aluminum extrusions used in Prusa and other 3D printers. Used in combination with the...

Four screws for every corner and 8 screws for every side.[blue] NO acrylic glass holder at the side where the hinge mechanisms are located!From this on the “Front” is where the hinges are.[green] At the location of the green circle you can drill a...

I did not try to 3d print everything in plastic if metal or wood made more sense and was faster/stronger/easier and not cost prohibitive.  3D Printing is mostly used for the connections and exact positioning of tubing.Everything here is my own design...

I illuminate my RepRap 3D printer's control panel with it. The LEDs require a 12-volt power supply which can be supplied by the printer electronics (Rumba Board). Material: ABS, 3mm thick Nozzle: arcol.hu hotend v4.1.1, 0.35mm diameter Printer: DIY...

What to print: Print these files: icarus-1.2.1-for-sherpa-mini-r1-normal.stl sherpa-mini-r1-dragon-mount-1.1.stl icarus-dial-holder-1.0.stl icarus-belt-peg-1.2.stl icarus-fan-duct-1.3.1.stl...

Remove the stock z-axis tops and replace with this light bar mount.Dual Mount Z-Axis Top No Switch: Same as Dual Mount Z-Axis Top with no hole for the power switch.&nbsp;&nbsp;Print instructionsRecommended Print Settings:Layer Height: 0.20mmInfill:...

How to make your own module for the phone holderIf you know how to use 3d designing software here are the dimensions to make your very own module for the Modular Phone Holder! All the modules use a very basic system: to start, the main rotating part...

Use with Right MMU2 Mount Z-Axis Top.&nbsp;Print instructionsRecommended Print Settings:Layer Height: 0.20mmInfill: 15% GyroidSupports: Build plate onlyOpen 3MF files in PrusaSlicer for preconfigured settingsRequired hardware:Aluminum u-channel24V...

Worlds are waiting.&nbsp;Designed on Tinkercad.Enforced supports are required on overhangs and the main bodies (see 3mf files).The main bodies can be glued together to create longer Cargo Pods.Super glue everything together.Start shipping cargo; the...

By doing so, I can now get more of the STLs to show up in 3D view on this site. The updated files have 10-18-23 dates and are renamed with "-remake" or "-k". 10-10-23 Update: Two items - Assembly Hints and Images added as a new section, and an...

There are plenty of good tutorials on that topic (including 3D printer mods adding Noctua fans with buck converters) so I have no intention to create another one here. You may need tools like a soldering iron and a multimeter to get the job done.The...

You only need the USB board and the motor to make it run.This was specifically made for making interactive 360 photos of 3D printed objects quickly, using video (takes about 10min), but it can also be used for making animated gif's, rotating objects...

Feel free to rescale as needed.Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1 -...

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ ~...