bass shaker sim rig 3d models

Designed to hold a Dayton Audio BST-1 either directly to the side of a 40 series profile or mounted on the top/bottom of a profile (Vertical version).

Some simple Amp holders for the mini USB amps I use to power the bass shaker setup for my Sim Racing Rig. The ones I have are for 2, 3 and 5 Amps. The exact amps I use are XINYI Sini Audio XY-C100H -...

This model was designed on fusion 360 to assemble a generic Rock Wood Bodyshaker to a Next Level GT-Lite simracing rig. Assembly with 4 M3x25mm Hex screws and nuts

A Simple Fix to Attach a Bass Shaker to Your Next Level Racing F-GT Rig Without Drilling Any Holes. ... Get the full scoop on how it's done in this video: https://youtu.be/al3gEAN6RiI You'll need 4x 60mm M8 bolts and 4x M8 nuts to get started.

All-wood simulator rig boasts an adjustable pedal plate for customized performance.

Send me a message, I am here to help.---------------------------------------------------------------For the top assemblies with even more modifications please see following model: Enhancements for Next Level Racing Flight Simulator Boeing Military...

An idea for a diy 40x80 extrusion sim rig.

This is my take on a sim racing rig

Hi, this is a Bass Shaker Mount for the Playseat Challenge Seat. ... Thanks for donating paypal.me/Charliethingy

Here's a 3 part video on how I did that showing the mount with the bass shaker attached: https://www.youtube.com/watch?v=OorVgHAXW_4 ***Tip:*** if you place the bar and Bass Shaker at on the front leg frame you'll get more vibration up the back of...

Here is the hardware i used to assemble and attach to my sim rig. Two M8x16 Two Washers for M8 boltsTwo roll in T-NutsOne M5x20One M5 nutI used the 80mm extension to raise the mount to be closer to my monitors. ...i then used the 90 degree extension to...

Sim racing setup I built based off my own design

... profile installation. ... The pre-drilled holes on your rig are specifically designed to accommodate M8 Bolts. ...If you need to use a smaller bolt instead, I can modify or provide the CAD part file so you can make the necessary adjustments yourself.

This is an ongoing project: a foldable simulator rig that doesn't require soldering. ... You can see it being put together in this YouTube video: https://www.youtube.com/watch?v=VWVZ4TFBBSk&feature=youtu.be In-game demonstration:...

This is a fundamental component of the T1000 sim racing system. To properly attach it, utilize 6mm x 60mm threaded fasteners and corresponding bolts for maximum stability. ...Additionally, 6mm x 10mm threaded fasteners and matching bolts are required to...

Thank to this adapter, you can mount bass shakers to your IKEA JÄRVFJÄLLET chair and bring your Sim Racing on another level. ...Bass shakers are mounted to place where armrests would be mounted.

Thank to this adapter, you can mount bass shakers to your [IKEA JÄRVFJÄLLET chair](https://www.ikea.com/us/en/p/jaervfjaellet-office-chair-glose-black-50363550/) and bring your Sim Racing on another level. ...Bass shakers are mounted to place where...

Wind Sim 3D Parts for my Sim-Lab P1-X Sim Rig. This bolts directly onto the 40x40x40 aluminium extrusion with 8mm hex bolts. I use tubing to then direct the air to my position. ...I have two of these wire up to the Arduinao Leanardo.

Dual shift knob holder for 8020 aluminum profile sim rig. Designed to hold two knobs with M12 x 1.5 thread. ...Requires x2 M6 bolts and t-nuts.

Sim racing rig cup holder. 3" ID, 3.5" deep. Designed to attach to 15 series extrusion with 1/4" hardware. ...Mounting holes are 1.5" on center.

Thank to this adapter, you can mount bass shakers to your IKEA JÄRVFJÄLLET chair and bring your Sim Racing on another level. ...Bass shakers are mounted to place where armrests would be mounted. Print Settings Printer Brand: Prusa Printer: Prusa Clone...

Angled mounting fixture for Elgato stream deck onto an aluminium profile sim rig (driving, flying etc) The stream deck will sit on the plate but i also secured with some hot glue

Hi guys,Remix of NobOwens wall mount, just modified to slide into 4080 aluminium extrusion sim race rig.tslot segments are offset to allow no supports, has no effect on stability.

Simple bracket to hold the Razer Nommo speakers to a Alu extrusion Sim Rig. Mounts on all 4040/8040 profiles, should work with 3030 as well. Uses M6 mounting hole. Holds the speaker pretty stable. ...I added some car tuning alu washers for looks.

Designed to mount a noctua NF-A14 industrialPPC for wind simulation to the side of the wheel uprights of a sim rig. ...Produces a pretty good interference fit with the rubber grommets squeezed between the part and the fan walls, additionally fixate with...

... from the keyboard I can redesign it to fit other keyboards also. Created these parts for my personal sim rig to get it bit cleaner and cover aluminium profile ends. ...Small fee due time used to design, print and test these to cover my costs a bit.

**BoM:** 2x clips or clips2 (L & R) 1x frame 1x Bass Shaker (Dayton Audio TT25 Puck Tactile Transducer) 4x M3x30 4x M3x20 6X M3 nut 2x self-locking M3 nut Clips are in two version for lower or higher (clips2) montage. ... Bracket also fits to clone...

I've made a laptop hanger for the Lenovo Legion 5 Pro sim rig, which is 31.5mm in internal size. It is compatible with any kind of aluminium sigma profile such as 4040, 8040, 8080, 12040, 16040, 16080, etc. It is a straightforward design that...

BoM: 2x clips (L & R) 1x frame 1x Bass Shaker (Dayton Audio TT25 Puck Tactile Transducer) 4x M3x30 4x M3x20 6X M3 nut 2x self-locking M3 nut Bracket also fits to clone of DA TT25 https://www.aliexpress.com/item/4000259931387.html 3D model are remixed...

Quick mount for the Saitek Commander unit for use as button box for Sim Racing. Can be mounted on any 4040/8040 alu extrusion. It hold the support bars of the two body parts of the keyboard, is pretty stable. Designed for M6 bolts. ... Source file can...