bartesian pod rack 3d models

I added a base plate 2.5" x 3" about the width of a cell phone so that it can fit into the Cell Phone mount that came with the Tri Pod. I made this project to hold the Blade Runner 2049 Binoculars from Jon-A-Tron that are on Instructables, Adam...

This is a POD for a AutoMeter Mini Tach 2 1/16". It includes an area for the upper light fixture and allows the 2 bolts to slide through at the rear..... This requires a 1/8" Foam to be added to the the part that goes around the column, this is to...

Flite Test Style power pod I designed this to be printed with minimal overhangs, since I seem to suck at calibrating my printer for bridges. There are other lighter designs on thingiverse, but my printer doesn't print them well. if you can handle...

I needed a pod to mount a nano FPV camera to a scratch built FPV wing using 6mm foamboard. There was nothing really around, so a few hours in OnShape and this is what i came up  with.The side and main plates offer a bit protection for the camera, the...

Printable motor pod for the Flite Test FT-Dart. I tried the version shared by @JGPlanes earlier here: https://www.thingiverse.com/thing:2828661, but found the dimensions were slightly off. Rather than waiting for him to make changes, I created my...

Update Feb 12th 2016 I've added a pod that includes the whip option, along with a side port where you can mount an extension cable and bend the external antenna down. The port has been extended to accommodate most flight controllers. Update Jan 14th...

To create a Martian 2 pod that can fit onto a Martian 2 frame without a top plate, simply cut along the arms of the bottom plate to form an X shape and use the original top plate as the sandwich plate for assembly. By rotating it 90 degrees, you'll...

Check my other posts for the [3D printable toothpick style frame](https://www.thingiverse.com/thing:3563189) and [Pod](https://www.thingiverse.com/thing:3547944) for the Caddx EOS2 and the Runcam new Runcam Nano. Recommended Setup ================ ...

The pod has a fixed 45 degree angle with plenty of protection for the DJI cam. ... Check out this video for some flight footage: https://youtu.be/e9bYZ-Wrias 5 inch race setup: FlyFive33 Switchback: https://flyfive33.eu/product/switchback/ ...

Porta-Pod E (E -  electronic version) From my LARPerator Kit I have 2 real AR-15's, one with a holographic red-dot and one with a 5-25x50 scope on it. The scoped AR is Gucci and still a bit heavy because of the massive scope on it. Thus, the need for...

So this version is a few mm shorter and the sidewalls are slightly thinner. Printable motor pod for the Flite Test FT-Dart. I tried the version @JGPlanes shared earlier here: <a...

Paint rack - Paint rack together and separate 3 heights

spice rack. ... holds 15 pots

for infinix2 pods

for infinix2 pods

3D printable speaker pod

3D printable speaker pod

A pod from pop1

Focus Pod - Zilenzio

peugeot 106 vent gauge pod

1/32 sized Gekko pod

Shoe Racks, Slipper Stand Chappal Storage Organizer Multi-Purpose

A dish rack where you can dry your dishes. ... A dish rack where you can dry your dishes.

Rack for my Macbook Air. ...The width is 305mmFit for standard monitor rack holes.Optimized size for printer Ender 3 S1 (22cm x 22cm)I also uploaded the rack without a width limit for more possible laptops to fit in.

rack

Rack

rack

Rack

DYE Alpha Paintball 160 Pod Wall Holder & 2 Pod Wall Holder.

Open-Rack Ready: Install Your Equipment in One of Seven Configurable Units