barbed hierodule 3d models

This design contains: - the barb fitting (rounded or with a hexagonal face) - a nut to screw on from the outside - rings to be used as seals - a wrench for the hexagonal fittings I created this design to get rid of waste water from my countertop...

A cutting-edge pack of 5 barbed wire obstacles includes 2 variants each - weathered and pristine. A total of 10 detailed objects are presented, as evident from the images provided. These realistic models come in five formats: -.blend, precisely...

... Wall Thickness - A safety measure added with 2.0mm thick walls. Output Connectors Ratio - Optimized with an ideal ratio of 1.8. Input Section: Number of Inputs - Only one input point required. Barb Count - 3 small bars for secure connections.

Inline connectors are utilized, with input and output barb counts both set to 4. A vault wall thickness of 2.0 is employed, and the design supports vault connections. ...The strength requirement for this design is rated at 4, while only one input and...

Three barbed, single sided Magdalenian harpoon. This is generalized, not based upon any particular artifact. When printed, sanded, stained/painted this will be useful in a teaching collection. I am presenting these 3d models to everyone, free of...

output_barb_count: Our system uses a well-thought-out design featuring 4 output bars per connector. input_units: Stay within international guidelines by utilizing only standard US measurement for our input options. vault_connector_ratio: As the...

Unfortunately the barbs had become very brittle and broke off. I tried super gluing it in place which held though the power outage but as soon as I moved the pump it came apart again. I felt like I should be able to repair this little guy since it...

Print it barb side up.The barb is 13 mm at the narrowest and 15.6 mm at the thickest, works perfectly for ½" PVC tubing, though getting it off can be tough. 

Connect your damaged Shop-Vac 5 Gallon hose using this hose barb; fix and mend the hose afterwards.

Barb fitting for a TotalPond 140 GPH Fountain Pump model # 52217 The barb fits 3/8" ID hose The lower portion fit's into the 13mm hole on the fountain pump. ... Printed standing straight up, I used supports around the bit of overhang around the base of...

Adapter not available anywhere 3/4" NPT to 5/8" Hose barb I'd recommend PETG, but any port in a storm.

Just my design of 1" male barb to 1" NPT for poly pipe. ...My watering system is made base on 1" poly, to connect valves need this staff.

This is a versatile 0.5 inch female NPT to 1 inch hose barb adapter, carefully crafted through innovative modifications of two distinct online adapter designs.

This is a fitting for a water pump requiring 1/2 FNPT to 1/2 ID tubing barb. ...Modified for 3d printing no supports.

... available for $30. ... Instructions: - Print the replacement barb at a precise 45-degree angle to ensure optimal strength and support on your build plate. ... Attach the new barb firmly to your venturi, allowing it to dry completely before proceeding.

... boost controller. ...The threads are 1/8" NPT, and the hose barb accommodates approximately 5/16" rubber vacuum hoses, with compatibility for 1/4" hoses as well. ...I printed the fitting at .1 or 0.05mm layers in ABS material, which proved effective.

Instructions Using the following options: Inputs: 1 Inline Junction Type: Round Input Units: Metric Inline Junction Width: 0.8 Strength: 1.0 Vault Wall Thickness: 2.0 Output Units: Metric Output Size: 18.4 Output Barb Count: 4 Vault Support: Yes...

The design features a cone1 wall thickness of 2, a barb spacing ratio of 2, a join height of 3, a cone2 height of 20, a cone2 wall thickness of 3, a cone1 height of 20, a cone1 maximum diameter of 6.3, a cone1 minimum diameter of 5.9, a cone2 barb...

Options: Outputs 1 Vault Connector Ratio 1.8 Output Size (US) .27 in Strength of Output 100% Vault Wall Thickness 2.0 mm Inline Junction Width 0.8 in Input Barb Count 3 Connector Type Inline Inputs 1 Vault Support Yes Input Size (US) 0.27 in Output...

This carabiner has two barbs in the hook, to prevent that the hook can slip out to the side. ...The round hole is 1mm smaller at both sides, so that it´s easier to hang keys in it.

Another piece that I needed from the store that I forgot to buy... ... Print with barb end pointing to build plate. ... Supports only to build plate (or it will mess up the NPT threads)

Brass hose fitting for 3/8" ID hose. ...Ferrules on barb end hold hose from slipping off. Use of hose clamp helps prevent leaks. 1/2" Male NPT thread on opp end. ...7/8" hex

Barb-type Hose Adapter for Lee Loadmaster Primer Catcher https://www.thingiverse.com/thing:3816679 Special thanks to ratatattat for the innovative remix idea. This barb-type adapter seamlessly connects a 1/2" OD wire wrap hose (Harbor Freight 66986)...

http://www.thingiverse.com/apps/customizer/run?thing_id=158717 Instructions Using the following options: input_units = metric inline_junction_type = angled connector_type = surface output_size = 5 mm output_units = metric inputs = 1 vault_support =...

This precise 3D model of a Low Poly Barbed Wire Obstacle comes packaged with five convenient file formats, catering to diverse design requirements. - A highly detailed blend format is available for artists familiar with Blender and Cycles. - An obj...

The Low Poly Barbed Wire Obstacle model features detailed geometry, and its barb is carefully crafted using a plane image. Some slight material adjustments may be required, depending on the 3D software program you use. Originally created in Blender...

... solidity and stability. Meanwhile, the tube barb design originated from 3M Respirator Bayonet Oxygen Tubing Adapter by kmcelroy82, although its horizontal orientation presented challenges during printing and attachment to a 3M respirator.

https://www.thingiverse.com/apps/customizer/run?thing_id=158717 Instructions Using the following settings: Vault Connector Ratio: 1.8 Inline Junction Type: Round Vault Support: Yes Strength Level: 1.0 Number of Outputs: 1 Vault Wall Thickness: 2.0mm...

http://www.thingiverse.com/apps/customizer/run?thing_id=158717 Instructions Using the following options: Output size set to .25 Inputs specified as 1 Input size set to .6875 Outputs designated as 1 Barbs on output set to 4 Barbs on input set to 3...

1/2 NPT shower to 1/4 OD barb (ID of tube) this tread has a 1.78deg taper so not sure it will fit ( it did fit without the taper for 1/4 in of tread engagement .. .this should help to engage fully) other side is 1/4 barb but its "oversized" a bit so...