baofeng uv 5r volume knob 3d models

Safety is Number One Priority -Crazy Russian Hacker PLEASE USE THE NEWER DATED PARTS ************************************************************************************************* This is a remix of the Baofeng UV-5R holder with mic slot by...

Comments and suggestions welcome.73 -bill "Safety is Number One Priority" -Crazy Russian Hacker PLEASE USE THE NEWER DATED PARTS This is a remix of the Baofeng UV-5R holder with mic slot by turbo2ltr: https://www.thingiverse.com/thing:1917427 The...

For assembly, you will need a dab of glue (I might recommend a little white craft glue), for the Locking Seat, then install the Locking Knob, then finally the Locking Pin (maybe another dab of glue). If you used craft glue, you should be able to...

This Knob is design to replace the original one on the UV5r And UV82. ... Is bigger size allow easier manipulation with gloves A hole for a small M3 headless screw allow you to secure it in place (not mandatory)

This is a belt clip for the baofeng uv5r, which is hotter than the normal one

A handy cap for the side buttons of the widely used UV-5R radio. The side buttons are uniquely vulnerable to accidental presses, especially when carried in a backpack where they can easily get triggered by movement. They remain fully functional even...

A modell to place your Baofeng radio with extended battery in so it will fit in a PRC 148 pocket.

... include purchasing a 3rd party mount. ... Remixed from Mike's [Baofeng Bike Mount](https://www.thingiverse.com/thing:756744/remixes) NOTE: This only works on JL Wranglers WIHTOUT power windows, since it press fits into the blank cubby on the dash.

I have printed it and verified that it fits the UV-5R charger, and the plan is to stick it to the right side of the driver's seat in front of my knee. It will be mounted with 3M Automotive Mounting Tape. I will plug the charger into a 400w inverter...

It protects the volume/on/off knob and transmit from being accidentally pressed, as designed. 2. Low profile. 3. Easy to install. 4. You can still remove/install the battery with the protector on. Cons of original model: 1. You can't press all...

Since I like to experiment with homebrew antennas a lot, I wanted to give my Baofeng a BNC connector for the antenna, to make it easier to quickly change the antenna. ... I used some readily available adapters but wanted some "bushings" to stabalize it...

Klickfast system for the Baofeng UV5R type radios. Use with the Klickfast belt mount https://www.thingiverse.com/thing:4675613 or the Klickfast Molle mount https://www.thingiverse.com/thing:4675631 . To use, insert your radio mount into the receiver...

However I upgraded the antennas for my UV-5Rs and the original print would not hold them. This will fit Luiton NA-771 and NAGOYA NA-771 antennas. If there are other NA-771 antennas on the market they may fit. ... I only have the 2 I listed above to...

This is my version of the UV-5R battery case for 18650 cells. The construction is quite simple to assemble without using industrial contacts. ... More details about assembly and print settings can be found in the video: ...

Baofeng Battery Lock Successfully Printed with Layer Height of 0.1 Millimeters, Functions as Expected.

This is a custom ham radio volume control designed specifically to fit Baofeng style radios, such as the Quensheng UV-R50 and the Baofeng BF-UVB2-Plus models. The design was inspired by the futuristic look of the Terminator movie franchise. This knob...

This piece fits over the volume/on knob at the top of a Baofeng UV5R ham radio and prevents it from rotating further. It is a snug slip fit and is a finicky piece to design with all the small detail. However this is really useful if you put the...

Wall mount holder for Baofeng UV-5R or GT-3TP and similar radios

This 3D printed part fits the Baofeng UV-5R radio. The radio is inserted into two slots in the lower part and then screwed using two attachment points on the radio. A cap covers the volume knob so that it cannot be turned accidentally. Elastic straps...

This 3D printed part fits the Baofeng UV-5R radio. The radio is inserted into two slots in the lower part and then screwed using two attachment points on the radio. A cap covers the volume knob so that it cannot be turned accidentally. Elastic straps...

I'm not a fan of the massive and unattractive original volume knob either. So, I created one by taking inspiration from the UV-9R Plus model's design, which also boasts a reference notch. For printing purposes, flex or semi-flex filament like TPU is...

... with your 3D printer's output. [EDIT 10/24/2019] GT-5TP_vol_knob_V7.stl added. Due to a likely plunger effect that can suddenly eject the knob from the installation after some time, I've designed a solution for the compressed air during insertion.

I don't like the huge and ugly original volume knob. So I drew one by taking a look at the UV-9R Plus one. ...It also features a reference notch. To be printed with flex or semiflex filament, tipically TPU it's a good choice. You can choose to print and...

Simple desk caddy for my Quansheng UV5K but designed to fit my Baofeng UV-5R as well.

Baofeng UV-5R Walkie Talkie Radio model ready for game engine or to place in any scene.

I just added the lettering and a base in Tinkercad.

Here are some mounting brackets and a screw included that will allow you to attach this hanger to your vehicle or whatever object suits your needs best.

I wasn't impressed with the commercial options I saw, so I designed this mount for the Beofeng UV5R. Provides solid retention for the radio. Holds it at the bottom using the shape of the base and the charger alignment slots. At the top, it uses...

Check the diameter of your antenna/connector and pick the appropriate size I have only printed both knobs in TPE. Have not checked fitment with other materials. V0 should work for PLA or the likes, It exactly matches the original on the shaft size....

... attach a support for the microphone. -------------------------------------------------------------------------------------------------- CAT Suport per tenir el Baofeng UV-5R sobre la taula. ...Opcionalment s'hi pot enganxar el suport pel micròfon.