baofeng uv 5r battery lock 3d models

To use, insert your radio mount into the receiver mount upside down then rotate right side up to lock into position and to remove, simply reverse the process. ...This will prevent your radio from falling from your belt as you move, walk, jump and run.

This is a belt clip for the baofeng uv5r, which is hotter than the normal one

A handy cap for the side buttons of the widely used UV-5R radio. The side buttons are uniquely vulnerable to accidental presses, especially when carried in a backpack where they can easily get triggered by movement. They remain fully functional even...

... include purchasing a 3rd party mount. ... Remixed from Mike's [Baofeng Bike Mount](https://www.thingiverse.com/thing:756744/remixes) NOTE: This only works on JL Wranglers WIHTOUT power windows, since it press fits into the blank cubby on the dash.

I have printed it and verified that it fits the UV-5R charger, and the plan is to stick it to the right side of the driver's seat in front of my knee. It will be mounted with 3M Automotive Mounting Tape. I will plug the charger into a 400w inverter...

Since I like to experiment with homebrew antennas a lot, I wanted to give my Baofeng a BNC connector for the antenna, to make it easier to quickly change the antenna. ... I used some readily available adapters but wanted some "bushings" to stabalize it...

Mine is almost a year old (including a SoCal summer) and has had no bending or warping. There are options for both the standard battery and the extended battery. I use a remote mic/speaker with an extension. ...This allows anyone in the LR3 to use the...

... a SoCal summer) and has had no bending or warping. There are options for both the standard battery and the extended battery. I use a remote mic/speaker with an extension. This allows anyone in the LR3 to use the radio. ... Category: Electronics

a charge bed for topping off the battery while in travel. With four M3 screws to good fix, and upper receptacle for bi-colored charging LED. ... Recomended charger: https://electronician.blogspot.com/2011/10/simple-ni-cd-charger-automatic.html ...

belt clip for a 2 inch wide belt, very very secure. ...you will need to remove the battery to take it on and off the belt. The clip uses the stock screws. ... 4 walls and 20% infill should do this just fine

However I upgraded the antennas for my UV-5Rs and the original print would not hold them. This will fit Luiton NA-771 and NAGOYA NA-771 antennas. If there are other NA-771 antennas on the market they may fit. ... I only have the 2 I listed above to...

... signs of warping or bending. For those looking to upgrade their LR3, there are two battery options available: standard and extended. ...I personally utilize the remote mic/speaker with an extension, granting anyone within reach access to the radio.

You can still remove/install the battery with the protector on. Cons of original model: 1. You can't press all of the side buttons because they are covered. 2. The power/volume protector breaks under hard use. It would last for a few range trips...

The ball in the picture is available here: https://www.thingiverse.com/thing:499086 To add the ball mount, I used M5 x 14 mm pan head philips bolts and M5 lock nuts. If you have longer bolts, a bushing on the bolt side will keep it from interfering...

Wall mount holder for Baofeng UV-5R or GT-3TP and similar radios

Simple desk caddy for my Quansheng UV5K but designed to fit my Baofeng UV-5R as well.

Baofeng UV-5R Walkie Talkie Radio model ready for game engine or to place in any scene.

I wasn't impressed with the commercial options I saw, so I designed this mount for the Beofeng UV5R. Provides solid retention for the radio. Holds it at the bottom using the shape of the base and the charger alignment slots. At the top, it uses...

I just added the lettering and a base in Tinkercad.

Here are some mounting brackets and a screw included that will allow you to attach this hanger to your vehicle or whatever object suits your needs best.

simple protection against turning the knob i use PETG filamentprint upright positionorginal screw to remain fixed

Replaces the rear ashtray with a mounting plate pre-drilled for a Baofeng UV-5R. I use this to mount a radio for driving tours to communicate with other drivers. I use a battery eliminator for power, an external antenna, and a speaker-mic. The...

... attach a support for the microphone. -------------------------------------------------------------------------------------------------- CAT Suport per tenir el Baofeng UV-5R sobre la taula. ...Opcionalment s'hi pot enganxar el suport pel micròfon.

Made some key modifications to the Baofeng battery lock. The original design was slightly off, so I tweaked it to perfection. Specifically, I enlarged the push part of the lock clip and the bottom wedge to ensure a snug fit on the battery pack. To...

A simple yet useful addition for any Baofeng enthusiast - a convenient volume knob. The accompanying SolidWorks source file enables users to customize the design according to their preferences. ...Additionally, Simplify3D factory files are provided,...

This is a RAM mount compatible holder for the Baofeng UV-5R FM mobile radio. The holder design includes a slot for using a vehicle powered battery eliminator if desired. A handful of these have accumulated thousands of miles of rough road use...

This 3D printed part fits the Baofeng UV-5R radio. The radio is inserted into two slots in the lower part and then screwed using two attachment points on the radio. A cap covers the volume knob so that it cannot be turned accidentally. Elastic straps...

This 3D printed part fits the Baofeng UV-5R radio. The radio is inserted into two slots in the lower part and then screwed using two attachment points on the radio. A cap covers the volume knob so that it cannot be turned accidentally. Elastic straps...

If you've got a broken plastic part in your stock Baofeng UV-5R belt clip, this is exactly what you'll need to get it up and running again! This design was actually inspired by my other, more advanced radio - the Wouxun KG-UV899. Make sure you still...

This model provides a replacement for the rear ashtray in an E46 with mounting holes specifically for a Baofeng UV-5R. It could be used to mount anything in that spot though.Two models are included, one that fits a little loose and one that fits a...