baofeng 25x4 3d models

Designed this stand cause after changing the stock antenna to a better/longer one gifted to me by my bf the radio could easily fall over and probably brake so i made us 2 of these! It doesn't hold tight on the radio and that means you just lift...

Just a simple socket adapter to use a Diamond SRH-771 antenna on the Bafeng UV-5R.

I liked the cupholder and the hollow remix. I remixed it again to make a clean and sturdy print without support.The I had to realize, that it was to tall. So I made a smaller version. I also moved the position of the radio more to the front. ...Now it...

<p>I have the same problem as most with the UV-5R. If you move the headset plug slightly, the radio will no longer work.<br/> There is already a solution for this here. ...However, I didn't like it because it is too bulky and you have to buy...

This is a custom clip designed to securely hold 5mm wide contacts onto the battery of a handheld two-way radio. Note: The contacts must be quad-A or triple-A sized, as larger AA-sized contacts are too wide to fit onto radio battery terminals. To...

<p>Original loop have sharp edges and useless for me so i made this replacement. ...Trim with knife if need it.</p>

An upgraded go-pro compatible holder for the UV5R radios. There is an added slot for better belt clip retention to help prevent movement under off-roading conditions. ...It also significantly helps reduce noise from the radio rattling around in the...

This is a remix of https://www.thingiverse.com/thing:2489979 the intent is to make a functional alternative that fits the extended batteries. I took the original design into meshmixer sliced it into 3 sections and stretched out the middle slice.

Sliced it even with 20% infill was going to use 50M+ to print yikes. Decided to make a plastic saver remix by hollowing out the inside of it. Imported to Tinkercad, made some holes and this is the result now. Big thanks to regsix7 for creating such...

The width of the smaller bracket is 53 mm and the width of the Medium is 70 mm. The thickness of the material is 5 mm throughout, so it can withstand use. ...The clip hole for both is the same size and fits both the phone and the microphone.

Inspired by https://www.thingiverse.com/thing:306288 and https://www.thingiverse.com/thing:2172755 There are two versions of volume braket - with integrated belt hook and without it. Version with belt hook can be used with original screws. ... For...

I have the same problem as most with the UV-5R. If you move the headset plug slightly, the radio will no longer work. There is already a solution for this here. However, I didn't like it because it is too bulky and you have to buy screws. The...

remix with a callsign on top and without callsign

The default radio knob seemed to constantly change when worn on a buoyancy aid - therefore I created a sleeker, and less snagable replacement. ...

A simple antenna holder that slides on to the belt clip for the UV-5R to reduce the vertical profile. ...good for travel or just keeping the radio in your pocket without worrying about the antenna.

Inserting the belt clip requires positioning it within the top portion of the device, which serves as a secure location for storing items like headphones or other accessories.

Fits my 2004 Silverado perfectly. ...I used an original STL design from EvilNebby in Tinkercad, scaled up the dimensions by 101%, and attached a custom microphone holder for seamless integration.

Print this with uprights vertical, adding support underneath the base only, then sand smooth or break away if it prints cleanly. This model loads into Cura upside down at 180 degrees, I'm unsure how to rectify that situation, but simply flipping it...

I have a few uv5r radios and always found them to be falling over, and generally disorganized.  I like my bench to be tidy so I modelled this tray which will hold a charger, and a radio. ... You can take your radio out of it's charger when it's done.The...

Customized version of https://www.thingiverse.com/thing:5277569 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5277569

Simple stand for up to 9 batteries

A very simple mount for my handheld radio. The bar is 22 mm - but as it is fixed with zip-ties, other diameters should word as well. I glued some foamed rubber on the surface for a better grip. May I try to print in with flexible filament to absorb...

Rewritten for optimal comprehension, the system has been completely rebuilt from the ground up. This was done to accommodate an accessory that could seamlessly integrate with a phone mount I already owned. ... ...

Modified to fit the center vent of a Grand Caravan 2011, fit perfectly!Printed in ABS

I needed a wall mount with mic and antenna holder. This thing was created using Tinkercad. ...Edit it online at https://www.tinkercad.com/things/aGq0WyZJ4rw

This is my version of the UV-5R battery case for 18650 cells. The construction is quite simple to assemble without using industrial contacts. ... More details about assembly and print settings can be found in the video: ...

Customized version of https://www.thingiverse.com/thing:5277569 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5277569

Batteries supplied with my radios were not reliable and I had some 18650 batteries that I decided to fit in these walkies. I used 10mm wide adhesive copper foil tape to wire the batteries in the tray. WARNING: original battery voltage says 7.4V but...

Simple dust protection shields delicate electronics from airborne debris and pollutants, safeguarding sensitive components within a clear plastic enclosure.

While there is quite a lot of overhang underneath the knob, its so small that support material is not too big a challenge.