ball lock keg connectors 3d models

This is a fundamental ball lock connector post designed for homebrew kegerators, specifically intended to facilitate line cleaning. Its use in water-tight or food-safe applications is not recommended. For effective cleaning of beer lines on my...

Hand driver to remove/assemble plastic cap on quick-release beer keg ball-lock connector. ... The driver is printed from ABS and helps prevent cracking the plastic assembly versus using a traditional screwdriver.

Hand-held tool removes or assembles plastic cap on quick-release beer keg ball-lock connector. ...The tool, printed from durable ABS plastic, prevents cracking of the plastic assembly when compared to using a conventional screwdriver.

These are caps for Ball Lock Keg connections on Cornelius kegs so that while in your kegerator, you can identify what tap each line goes to. ...I slightly modified the original authors STL file in TinkerCad to include #'s to accommodate up to 7 taps.

I just slap a small cap over my keg couplers. ...It's a snug fit around the O-rings when I'm using my printer on my kegs.

This is a dummy insert for a Cornelius keg ball lock connector with a hole for liquid to flow through. ...It's really useful for cleaning out keg lines without taking apart the fittings.

A rapid-disconnect fitting is designed for a ball lock Cornelius keg, featuring an MFL connection on the beverage end. ...The product excludes internal modeling.

I wanted a one piece adaptor which fitted a hoze lock and my ball lock keg posts. This is a ball lock (gas or liquid fits) to Hozelock/standard UK hose pipe fitting. I put two rubber washers on which has made it water tight under mains pressure.

If you find that you cannot push the thing in far enough to get the balls to lock, then use a screwdriver to deepen the hole for the pin in the top. It should be okay, as it only opens the valve about 1mm. ... DesignSpark Mechanical files are included...

This holds the poppet valve open, seals and allows the hose to be flushed, I needed 2 (of each)for my keg transfer lines with an inlet or outlet both ends. The black version is 15.5mm diameter body and the white is 16mm. Print Settings Printer Brand:...

Tap handle lock with adjustable screw. Works great on my setup! I used PLA with supports - lay the main body on its side and print with supports. The bolt prints fine standing without supports. ... PETG would be ok, but the higher stiffness of PLA is...

Keeper tracks picnic supplies in designated cooler space.

Easy gas release for Pin Lock Cornelius keg. ...REMIXED FROM snowveil original design:(<a href="https://www.thingiverse.com/thing:2593958">https://www.thingiverse.com/thing:2593958</a>)</p>

This is a wrench for removing and tightening the posts on a pin-lock ('corny' or cornelius style) 5 gallon keg. The posts normally require a 13/16" socket with either 2 (gas) or 3 (liquid) slots cut out for the pins. This fits both gas and liquid...

This is a wrench for removing and tightening the posts on a pin-lock ('corny' or cornelius style) 5 gallon keg. The posts normally require a 13/16" socket with either 2 (gas) or 3 (liquid) slots cut out for the pins. This fits both gas and liquid...

Twist a Pin Lock Cornelius keg without a built-in pressure release valve into place, holding the gas poppet down and allowing pressure to escape through the post. ...The Makergeeks Raptor PLA printed at 20% infill works effectively.

CIP Ball for Marks Keg Washer

CIP Ball for Marks Keg Washer

Added a ring for hanging on a keg to snowveil original design:(https://www.thingiverse.com/thing:2593958)

it is simple laur lock to a sure uinedirectional injection of narcotic drugs

... ...It fits on ball lock locks with the "thicker" rubber collar on top. Print instructionsLay the model flat on one of the smaller sides. ...I printed it without support on a MK3S in PLA.

This is a simple holder for the KegLand short tap shafts (https://de.aliexpress.com/item/4001135458268.html?spm=a2g0x.12010612.8148356.47.e4537a537w78OF). It fits on ball lock locks with the "thicker" rubber collar on top. Print instructionsLay the...

The original phrase "Sub Plate Locks" has been rephrased as "Locks for Subplates." By doing so, the meaning remains unchanged, but it presents the information in a slightly different manner. ...This new version maintains the 60-word limit and avoids...

A keg suited for miniatures in 28mm scale.

This set contains various types of ball joint connectors and attachments for quickly building strong and malleable phone mounts and tripods. The connectors are also ported for electrical wiring so you can get creative, and come with wrenches. Use...

The player is searching for a keg to add to their collection in Dungeon Defenders Awakened.

This is an adapter specifically crafted to connect a garden hose to a ball lock, making it perfect for thoroughly sanitizing a home brewery setup.

HDL 20mm Klix Lock ConnectorsPart #: T6383Part #: T6387

Данный гидрозатвор подходит для ПЭТ-кег с винтовыми разбирающимися головками. Чтобы его использовать, необходимо снять заборную головку, которая состоит из основного блока и прижимной шайбы с резьбой. ...Вместо основного блока использовать "body1",...

Opens ball lock style couplers used with Cornelius (Corny) style soda kegs, often used in homebrewing. Very useful for cleaning and drying lines. ...Fits both gas and liquid couplers.