bakery 3d model

Some photos of the printed mod installed on the machine may differ from the STL due to the fact that my machine is a prototype, and I decided to change some details after discovering potential issues (so I updated the models, but for lack of time, I...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_width = 100 use_mouse_ears = 0 pattern_element_overlap = 52 stencil_shape = 3 custom_back_camera_y_size = 20...

Assembly Video: https://youtu.be/GqohsdSTQrc Using"2mm Male Female Banana Plug Connector for RC Model ESC Motor Speaker" to convert Foster Connectors to electrical connectors -concentric BNC like. The printed parts hold these 2mm contacts in place...

You have arrived at the "first three faces" - model one above. Next form a plane from the intersection points and the axis of rotation. Cut away from that plane. Voilà. Octahedron. NEW: Ten-sided added, and rounded and squished. Also blank. Simply...

... If this is the case, and accuracy is important, you should scale up the dimensions a little bit to compensate. I only tested this for small gaskets. If the model proves unpractical for larger gaskets, contact me and I'll see how I can improve it.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

In order to make it much easier to assemble the case with the RPi4, a few changes were made:Divided the lower part in two halves for easier inserting ofRaspberry Pi;Added snap fit link between upper case and lower case;Using four M2.5x4 screws is...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_y_position = 0 custom_top_port_x_position = -10 use_stencil = 0 pattern_line_thickness = 32 stencil_pattern_element_shape = 4...

Also also: if you get sick of chasing dice when they fire out of the bottom of the dice tower at high speed and scatter over the edge of the table, I would suggest you head over to [**domino6713's dice tower courtyard...

Because of the simple geometry of the Box and the Pieces, these modest settings produce a very nice model in a relatively short print time. Please Note: Although I have not provided the solution here, I will respond to personal Thingiverse messages...

This model is extremely water-resistant, highly buoyant, and accelerates quickly with my setup. I printed this on my Ender 3 using split parts for easier printing or a single part if your printer can handle the height. The hatch measures 26mm deep,...

Print Settings Printer: FlashForge Rafts: No Supports: No Resolution: .2mm (Medium) Infill: 20% Doesn't matter Notes: For the most part, I intended these to print without supports; however, the housing is so wiggly that it needed some once I...

I changed the position of the threaded inserts and added additional to replace the hex nuts. Modified the cable paths and tie wrap holes for easier printing, and thickened up some sections to print better. Modified how the front and rear clamp...

To assemble: Note - this is a somewhat challenging model to assemble, with a lot of parts, and a lot of tight-fitting pins to hold the parts of the toy together. You may also have to clean up a lot of support off the oddly-shaped pieces as not much...

Tonight, I finally decided to model the hinges in fusion and print out new ones. The test seems to work well enough. So I'm printing them with a roll of ProtoPasta Carbon FIber HTLPA. This will be my first real test of this filament. I will update...

unless you have a special edition like a Porsche, Mercedes, or older Audi, VW, or BMW model, which is what I have. For most of these special editions, the original push bar won't fit. I found a design on Thingiverse called *Klein-laui* and tested...

;-) How did I end up with two of these devices? At first I bought the 2TB version and wanted to replace the HDD with a 5TB model. I tried several things, but nothing worked. With vaccation ahead, I ordered a second device with 3TB. The electronics of...

Model of the pusher cap and the skirt part used on an On/Off switch combination cast aluminum IP40 case The case with two momentary switches made more than 40 years ago in the GDR (do not call it East Germany, please) works still perfectly fine. It...

Enjoy my Ulvheim Small Merchant House. It came from my Patreon February Release. Thanks to all my supporters and to Markus Kruse / Terrain4Print, creator of the Ulvheim City. This model is supportless as usual. :)</p> <p>Discover my Ulvheim Remixes...

If you have a V3 or want to upgrade your V2 to a V3, go to the V3 mod.&nbsp;Minimalist parts required to convert the LumenPnP from v-slot rollers to linear rails. This preserves the overall dimensions and travel of the machine, as well as maintaining...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

&nbsp;Some require the models to be rotated so that they share space with their neighbors.AssemblyEach tray is comprised of 4 (or 5) rows. &nbsp;Each row comes in two parts (so they fit on smaller printers like the Prusa Mini) and need to be glued...

The COMPLETE The Bloodhunt bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The Bloodhunt Knights were the first Soulless Vampire troops to be sent to the mortal lands of...

*** UPDATE 30/06/2021 *** As lots of people have noticed, the original model is a ridiculous reducer at a ratio of about 3:1 from the original duct. I've now added a design that is much larger (labelled as "Full Size") and can be printed in three...

idk what slicer or print settings were used on the original print, but I had to redo the entire geometry of that area to get it to print right without disturbing the bevel of the rest of that model. Unfortunately, given I don't have the original...