backup camera license plate mount 3d models
693542 3d models found related to backup camera license plate mount.
thingiverse
I installed a backup camera on my Suburban and encountered a challenge finding a suitable mounting solution. To overcome this issue, I devised a plan that requires two M3 heatset inserts and an M3 socket head cap screw. The camera in question can be...
thingiverse
A reversing camera mount for Ford Crown Victorias that replaces the license plate light. It should fit 1998-2012 Crown Vics and Mercury Grand Marquis, possibly Town Cars - I have not looked at the license plate light on those. It was designed to...
thingiverse
I recently installed a new head unit and reverse/backup camera on my 2008 Scion xD, but I ran into a problem mounting it: if I used the license plate screws, they blocked the tailgate latch access and obscured part of the license plate that showed...
thingiverse
... Accord Coupe. Also I wanted to mount the bracket behind the license plate, not in front. (Some states will ticket you if the plate is obscured at all.) This design was done in OpenSCAD and you can customize it! All dimensions are in mm. ...
thingiverse
license plates perfectly and features two mounting holes for securing a small square camera in place. Two slots are also included for M3 nuts that keep the camera firmly attached to the bracket. ...The camera mounting holes are 32mm apart, while the...
thingiverse
... considered attaching the camera to its intended location, but unfortunately, the camera's field of view was obstructed by the tailgate when it swung open. To overcome this issue, I designed and fabricated a custom license plate mount for the camera.
thingiverse
I picked up a wireless rearview camera kit but it was lacking a mounting bracket so I fabricated my own solution.
thingiverse
... plate. The 1.5" model is what I have installed. If you still do not like the amount of light in the camera, try the 1.75" model, but be careful as law enforcement may be more likely to pull you over if they cannot read your license plate.
thingiverse
Rendering of a Jeep backup camera mount using spare tire as the mount location. ...
thingiverse
Buy a license plate-mounted backup camera and transplant it into this versatile mount that lets you put it anywhere you need it. I mounted mine directly above my van's rear window for optimal visibility. ... You'll need: - (1) license plate-mounted...
thingiverse
The mount for my generic chinese backup camera rusted away. I made a new one. Guaranteed to fit as long as you happen to have the same camera. ...
cults3d
The mount for my generic chinese backup camera rusted away. I made a new one. ... Guaranteed to fit as long as you happen to have the same camera.
thingiverse
This greatly improves the view in the backup camera while still allowing the license plate to be illuminated. You need to print two, and preferably in some UV stable material so they last longer outdoors. Edit: The "R" version is a couple...
prusaprinters
Dodge Ram1500 Backup Camera MountYear: 2015 Dodge Ram1500 (May fit other model years)Adapted to utilize existing holes for dash board coin area.Compatible for Type-S after market rear camera LCD, utilizing Bluetooth license plate camera.Additional...
thingiverse
This is a remix from License Plate Camera Mount by MongooseNX with just a few modifications to fit my camera from Niloghap Universal on Amazon. Link for camera. ... ...
thingiverse
I enhanced this by adding a hole in the center to accommodate a small backup camera, which has a slimmer rim around its edge to match the latches on the device. Improved version: http://www.thingiverse.com/thing:767820 Instructions...
prusaprinters
Lexus GX470 Backup Camera MountThis model is a simple 3D printable mount for attaching an aftermarket backup camera to the OEM mounting location on a GX 470 SUV. The mount was designed for use with this "NATIKA Backup Camera IP69K" however it may...
thingiverse
Human error led to a broken third brake light, prompting me to install a backup camera on the fly. ...I quickly switched out the faulty component with a shiny new one, using square nuts for added stability and 3mm by 16mm bolts for precision.
thingiverse
This mirror installation is intended to assist with parking and does not provide a good angle (camera is mounted too low) for full time use while driving. This mount is designed to be used with two brass heat set inserts and four M3 screws. ... The...
thingiverse
To keep my license plate stickers intact and give my camera a sturdy anchor point, I decided to modify the simple frame that came with it. ...The holes were left out intentionally, allowing you to drill them in exactly where your specific camera...
thingiverse
... I put double sided alien tape a well as two car clips to attach it (had to drill two small holes for the car clips). I hot glued the camera from the back to seal it in and left the front just pressed against the opening with no extra protection.
thingiverse
Customized version of https://www.thingiverse.com/thing:4680394 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4680394
thingiverse
Customized version of https://www.thingiverse.com/thing:4680394 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4680394
thingiverse
Since I preferred positioning the camera directly in the center of my RV, I designed and 3D printed a custom mounting plate that replaces the original aluminum bracket. The new plate is then attached to the vehicle using strong Gorilla Mounting Tape,...
thingiverse
This is a backup camera mount for an NC Miata with the Advanced Keyless Entry (AKE) package. It a derivative design originally posted by "kiddingme". It is designed around the Nakita backup camera and moment buttons available on Amazon. It...
prusaprinters
Since I wanted to have the camera in the middle of the back end of my RV, I created a mounting plate that replaces the aluminum bracket and gets mounted to the vehicle using "Gorilla" mounting tape. ...I used PETG since this is for outdoor use. Parts...
thingiverse
Needed a Mount for My Backup Camera After Taking Off My Chevy Silverado 2500's Tailgate and Adding a Utility Cap. Used ABS Material to Make It. I Chose These Printer Settings to Get It Done Right. ... Printer: Powerspec Rafts: Doesn't Matter Supports:...
thingiverse
Made for my 2007 Toyota FJ Cruiser, I purchased a brand new radio featuring an LCD screen and discovered it came equipped with backup camera capability thanks to the provided camera. However, I was unaware of where exactly to position it until I...