baby model

...There is a mistake in my model of Geeetech's hot end - the three Bowden couplers are rotated by 180deg. This is not an issue, just don't get confused when you note the parts seem to go together the other way round! 4) Assuming you fit two fans...

Alexander is depicted here with large eyes with modeled lids, slightly parted lips, and the characteristic creased forehead. His thick leonine hair is swept up at the forehead in with locks breaking to the left and right. Deep drill work is used...

15.09.23 - Further updated design - Leaner models and thanks to a test printer from the handy discord community, I have included two versions - a no frills neat and straight one as well as a nice curvy one. Please do continue to test print and...

i believe there are 4 models, 2MB and 16MB, both with and without a 3.5mm jack. any of them should work, but i did not use the headphone jack. 2 Power switches: the reason there are 2 power switches, is one is a true power switch that kills...

On the X-Max you can have it installed all the time but I'm unsure of the other supported printer models.Print SettingsPrint the carriage in high temp resistant filament. I recommend using Polycarbonate (PC), a PC blend such as PC-FR (flame retardant...

You may have to insert a custom hole for a usb lead depending on your mounting position, this could be done in the model, or via a drill after printing. You will need to do some tweaking to keep the led matrix against the grid. This can be via...

Model says 119mm, which would be close.???---------------------------------------------------------------------------------------------------------Changelog: Version 6.115.Feb.22Version 6.1 has been released as experimental files. They should...

Thus, this pot for succulents turned out.Models added in two types, with a drain hole and stand, and also without, for example for cacti. You can also scale the model to fit the size you need when printing. Parts links below: TopZeal Filament ABS ...

Update 5/28/2023: Replaced drone reed tongue with an improved model with better tone.Quick StartIf you don't want to read all the text, the quick way to jump in and have a playable instrument (without the bag) is to just make the chanter. The 3MF...

The fuse holder that the panel cutout is designed for is marked "JEF" inside the fuse cover, and I believe this is that model.2A blade fuse (or source a single fuse locally): From banggood20mm diameter circular snap-fit panel-mounted power...

The previous model I partly cut out on the laser, while the Creality K1 with its 600 mm/s printing speed allows me to not only create but also print all the parts (well, you could print the previous one, but it's too much for my nervous system). This...

You can download this model in four scales (1:40, 1:80, 1:160, 1:200), but I don't know if they are fully printable, nor which is the best way to print it. That's why I presented it in three split options: front and back; right and left; and top and...

This is easily the most cartoonish model I've ever made, since there are not so many topological features recognisable from space, so I exaggerate some placed to be seen in the model. For example, there is a tiny cube representing the Grayskull...

I didn't print out the new model myself, but it should work just fine. </li> <li>If you haven't already, attach the leaves. This can be done by first inserting the top of the leaf mount (the pointed end), and the rotating down. It should just sit in...

In the leg itself, I also cut an M5 thread and simply screwed a hairpin with an inserted nut into the leg, it got a tight fix.Also added a model of the controller case cover with an additional hole for the connector. But I didn't print a new one, I...

Of course, it takes a long time to print such a thing, nevertheless there is a model for a printer, and of course for a laser in DXF format.Although the easiest way is to stick crocodiles into polystyrene, but as my practice shows, at the right...

&nbsp;Often, designs with tight tolerances fuse together when printed at higher layer height and I am leveraging that in my model by making the clearances large in order to print fast via a 0.28 layer height. &nbsp;For my printer, it prints fast and...

This is a followup to: Lack Attack#3: Koppla the Lack: https://www.prusaprinters.org/prints/15919-lack-attack-3-koppla-the-lack-aka-power-the-lack-s without further adieu.... Attack 4: ENCLOSE THE LACK Its been a while since my last update, mostly as...

The plate is mostly an example, but it fits that model well.Added a .step file for a power plate blank, which will make it easy to modify to a different connector.These plates are printed with the front facing plane down. I have not printed a full...

Additionally you will need the parts listed in the BOM below.&nbsp;ChangesVersion 5.0 contains many tiny changes to the heads geometry making printing a little bit easier and optimizing the model for both .6mm and .4mm nozzles, allowing faster and...

Additional Required Components PSU Mount If you're using the Ender 3, you're fine to use the original "Ender 3 Remote PSU Mount," but if like me you've got a Pro,make sure to use the modified version, "PSU Top Mount for Ender 3 Pro." Note...

My dock design is posted separately as it is not dependent on this toolboard mount or even this extruder setup.In future, I plan to add support for the stock aluminum gantry... the hole pattern is a bit different so this one only works on the CF...

Our business model is centered around building trust with our customers, and we strive to maintain the highest standards of professionalism in every transaction. We understand that trust is essential in any business relationship, and we work...

- Update 10/7/2020 [Available here](https://cults3d.com/en/3d-model/tool/3dls-the-full-belt-free-printer-from-morninglion-industries) to download. Moving away from Thingiverse. - Update 4/29/2021 Added the heavy duty Y axis motor mount i made...

In an normal print that would equal a model with 600 mm in height with one tool change per layer. Update 24 I've just published a new "Revolver" option here. Here you can see it in action: https://youtu.be/uA2HJwa0xys I decided to make an remix...

And I will gather comments, if any come, then evaluate if improving the model is requiredAs a final word:With this PRUSA MK3/S/S+ the fun in 3DPrinting is back, however Prototyping is a bitch )); The picture below shows not even half of the waste, so...

The amount of time to tune the parts after printing is drastically decreased, as most parts can now be used and installed right out of the box (chapter "Afterwork" is updated accordingly)Change notes:changed Revolver_Body_Top to hold the cylinder...

Spin the original text of this Thingiverse model [here](http://www.thingiverse.com/thing:46884) using the Customizer! Create your own version with these options: qr\_y=0, qr\_x=0, tag\_height=80, tag\_width=80, perimeter=-1000, corner\_radius=10,...

This is an experimental feature for TheprofessorODK to add metal spikes to the model.If you could take a picture of an actual print, please "comment" and attach the picture. - I am curious to see your uses in the wild!</strong></i></p><p>If you like...

The assembly takes about half an hour.Designed with Autodesk Fusion 360All parts are designed to be printed without material supports ### Parts to be printed - The main body (choose the model corresponding to your hotend : E3Dv6 or XCR-BP6) - The...