b29 rc plane 3d models

complete solid works model

A tail wheel frame for my Hobbyking Hummer.

To install the engine mount on the Axon FPV flyer, place it within the square tube. ...This component is relatively insensitive to layer height and shell count; try printing it with four shells and a 30% infill for optimal results without any issues.

small project for college and testing

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

This is an ultra-fast 3D-printable pylon racer designed for thrilling speeds. Its impressive wingspan stretches to about 600mm, propelling it to incredible velocities of over 100 km/h and potentially reaching as high as 140 or even 160 km/h. ...The...

Modified my Hybrid 3d printed fuselage with foamboard wing and tail to be a tractor style. This cut down on weight and made CG easier. I used less than (2) 20"x30" Readi-board sheets total for the wing/tail components. The fuselage consists of...

I've specifically crafted these pants for the Hall Bulldog Racer model boasting a massive 1200mm wingspan. Measuring approximately 180mm in length, they boast a spacious compartment to accommodate a substantial 60-70mm wheel. ...Initially tested with...

I'm intrigued by the concept of 3D printed aircraft, but their weight and durability are significant hurdles. Nevertheless, I've designed this fuselage to showcase the potential of 3D printing in specific situations. The wing and tail surfaces will...

Publish your work and enjoy the thrill of creation!

These are wheels for radio control airplanes. I modeled them after 35" Alaskan Bushwheels. I've included models for 50 mm (2"), 44 mm (1.75"), and 15 mm (1") with 1.5 mm and 3 mm axle sizes. Print them in two halves, clean the axle holes out with...

We're planning to 3D print Weel (däck) using flexible filament, but so far we haven't attempted printing it with that material yet. ...The rest of our prints have been made from PLA or ABS.

People are creating models specifically designed to be printed using three-dimensional printers.

A University Assignment Task Project at University University-Based Task Assignment Task for Uni Project College Work: A Project An Academic Endeavor: The University Project The University Work - A Project Uni Assignment: The Project ...

This is just a simple power pod to fit these...

Two sleek concepts to elevate your aircraft's aerodynamics effortlessly.

PLA 25% https://youtube.com/shorts/6cylg_HfPPI?feature=share

I'm building a power pod for my drone that's surprisingly simple to print. It requires two servos - I'm using 9g ones but you can use 2212 or 2208 motors instead, as well as an ESC and a LiPo battery with a maximum size of 31x34x120mm. Additionally,...

This is a bespoke wheel cover designed specifically for my inflatable aircraft. ...I've configured the infill setting to a mere 5%.

The diameter is 30 millimeters and the central aperture measures 1.2 millimeters.

This hinge is engineered to attach seamlessly onto control panels, yet its design allows for effortless modification to accommodate screw installation if desired. ...Through strategic mating within the assembly process, the hinge can be manipulated to...

Multiplex Minimag RC Plane Landing Gear Holder for Replacement When Damaged. ... This landing gear holder is designed to serve as a replacement part for the Multiplex Minimag RC plane in case the original one gets damaged.

An RC plane featuring a flying-wing design is constructed using balsa wood for its ribs and structure.

Velocity Stack RC Plane - 19mm Carb Hole, 30mm Screw Distance, and 4mm Holes for Easy Installation; Compatible with MVVS 58cc Engine, Scalable to Other Models as Well.

3D printed parts for 68cm chuck glider conversion to long range RC plane. ... Flight video: https://www.youtube.com/watch?v=ZKMeOlN4PBM

Replacement Part for H-King Super Kinetic RC Plane Propeller Mount - Includes Everything Needed for a Quick Fix, No Additional Parts Required if You Have the Broken Piece.

This is a support for 4700uf capacitor (spektrum receiver voltage security), to install into a rc plane , avoid the capacitor to move during the flight and break the weldings.

includes all files for Solidworks 2022-23 to open a rc plane with movable control surfaces. servos and control surfaces are linked so they move in unison! ... https://youtu.be/7Zyuz5HYdtY

This is an attachment system for mounting motors to the wings of a Volantex Ranger 2000 remote control aircraft. ...Twin Engine Volantex Ranger 2000 RC Plane Build - Pusher to Tractor Conversion https://www.youtube.com/watch?v=Psh2D7V-0ug