b model macks

I could not prevent warping completely but using a strong construction lamp to heat up the model seemed to improve the result. I am glad for any tips on how to prevent warping. (I am new to 3D printing and so far brims did not prevent warping, and...

I was unable to find a free CAD model of the G5 on the internet. assistant Greetings, I started this endeavor to obtain dimensions for making a wooden housing specifically for the front area of a G5 device. Could someone here help with creating more...

On my version, I suggest that you start with 4 seeds in each of the 12 pits (print 4 copies of the 12 seed model and then separate them using nail clippers or small scissors). Increase the number of seeds in each pit progressively to increase the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

It was created by taking the NIH approved visor and flattening with patterning software and modeled tabs so that it can be added to the Prusa 4-hole layout. The removable visor can be 3D printed or laser cut for maximum efficiency. I have tried 3D...

There is a tight-thread version of all the models for those wanting a tighter fit or using a resin printer. Caps Flat Cap Flat Cap with GB Logo Cap with 3/4" Loom Stub Cap with 3/4" Loom Stub and Circuit Passthrough Cap with GX-20 Geometry Cap with...

I will upload my attempts, but I advise only using them for modeling purposes only, or if you can get them machined out of aluminum or something. Only then will they be strong enough. If your stem is too low or your cable housing is too short, then...

Note: I accidentally had two ⅔ marks on the outer ring in the original model. That has since been corrected but I haven't had a chance to print out a replacement, so the pictures still have the typo</p><h3>How to use</h3><p>Pick a measurement disk...

While it worked OK for most things, there came a time when I was trying to print a model with steeply overhanging points and the stock cooling just wouldn't cut it. I designed this adapter to allow a standard 5015 radial fan (24 volt, 0.1 amp) to be...

This new model boasts significant durability enhancements, enabling it to withstand heavy grounding without sustaining terminal damage - a critical feature for FPV enthusiasts, especially during the learning phase. I won't claim that it matches the...

[Medium Sized Model - 25mm Base] [Presupported in 32mm & 75mm scale]   The third child of Tharador, Renmaeth is the custodian of his body, the continent of Tharador. In the Age of Creation she shaped the mountains, tended the forests, sanded the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Make some extras in case you break some while inserting into the coupler.&nbsp;Sizing and tolerance:Model dimensions were adjusted to print at desired size. Your printer may give slightly different results and one part or another may need slight...

Modeled to look like a pirates spyglass, this kaleidoscope will be so much fun to play with! I printed in primary colors to preserve that playfulness. The pieces should slide together right off the print bed. This was designed so that the Barrel...

The bearing is model 6000. I would get one that is sealed to keep the saw-dust out. You may need to do some small scaling with your slicer to get the sizes correct. For my printer the bearing easily presses into the Depth stop, and the collar...

Great model from mz4250. Remixed to no base and support free again. https://youtu.be/J8bSrSSTLVE <iframe width="560" height="315" src="https://www.youtube.com/embed/J8bSrSSTLVE" frameborder="0" allow="accelerometer; autoplay; clipboard-write;...

License The "Drawer System" models (.stl) are licensed under the CC BY license by Code and Make. The "Drawer System" code (.scad) is licensed under The MIT License by Code and Make. Note: 'BSD' license has been selected as it is the closest...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

* Supports: Yes (if using Cura we recommend using the [Tree supports](https://support.ultimaker.com/hc/en-us/articles/360012614559-Experimental-settings) option and adding a 'Brim' to help the Tree supports adhere to your print bed) * Rafts: Doesn't...

Use at your own risk!!Check out the current version of this design here. This design is tested and ready for use, but only uses one blower, not two.</strong></p><h3>Basics</h3><p>This design stemmed from my desire to create a perfectly controlled and...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

The extra space available in a Volcano setup would allow much more open channels and sweeping paths, and I would like to improve the Volcano version in future, but this will require significant modelling work which I just don't have time for at the...

... You'll hear of a good change once more after fixing and updating the walls here: with even those not fully set designs being optimized properly with a little extra bit going onto your current model too, this will look awesome when everything’s set!

The next version will likely have longer front arms, a thinner and shorter middle section, and a removable gimbal mount for storage and travel (for my model of gimbal, Tarot T4-3D, but hopefully can be adapted for others of similar size). Printing...

Before you merge them, DUPLICATE the logo "hole" model (Ctrl D) do not use copy paste it will "shift" duplicate will keep it where it is. Now shift select the body and merge to make your hole cut. You will note you still have the duplicate hole. Now...

Previous model description: I hooked up a 1400mah battery and drove this home from my local park around 500-600 meters with no heat issues affecting the PLA print. I have used this around the house quite a bit with the camera, and it works well. The...

Particularly VERY IMPORTANT you need to change the setting from the default Negative Image to Positive Image. Adjust the Model Settings as I have shown in this Thing images. The Size (width) MUST be 150mm. Also I suggest reducing the thinnest layer...

- Replaced PZ20 circuit's LDO with a simpler model with higher input voltage range - Added second LDO for dedicated supply to LED's - Isolated TH1 from ground plane to address vdroop effecting thermal readings - Added grounding vias for edges and...

Now, everything will just fit without removing the box insert.ModelQtyDescriptionquacks-chip-box.stl2Boxes for Red, Green, Blue, and Yellow ingredientsquacks-chip-lid.stl2Lids for those boxesquacks-misc-box.stl1Box for the miscellaneous ingredients...