axolotl model

The casing has a channel modeled in the side to accommodate the ribbon cable coming out from the Raspberry Pi. 3) Insert the smaller end of the ribbon cable into the Raspberry Pi Camera Module, then place the module into the view port. The view port...

It is possible that a future will make and upload a model of that piece. In the meantime, if anyone knows where to get suitable pads, please let me know. As I was saying, I started to hang them on the screw. Since the surface of the screw with the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 3 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

The 3D model is solid. To make the vane pattern in it, set the number of top and bottom layers to zero and select a grid or triangular infill with a distance of about 10mm between lines. To ensure rigidity, aim for at least 1mm walls (3 perimeters at...

I think the steel should slide easily against most rigid plastics but better safe than sorry. Use Instructions: Print the model Remove the heat sink, tubes, retaining screws, and any heater or thermistor -- only the hot block and heat break should...

Sincethis design is compatible with a whole variety of lampshades, be aware that somelampshades will have to be scaled down or up to fit the base's default settings. Base- Layer height: up to 0.3mm is fine, there's little detail on the Z-axis-...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_radius = 6 custom_top_port_corner_radius = 5 custom_back_extra_port_y_position = 30 pattern_line_thickness = 20...

The picture of my working bitx40 model does not have the SPEAKER MIC wired up yet -still waiting for 2.5mm stereo jack. Files and features are subject to CHANGE. I will attempt to post relevant details with revision bumps as they occur. Also,...

... find sellers on Amazon.com or Aliexpress.com. This is still a working project. I will update the bill of materials I used, add more models for RPi 3, and sensors when they are done. ...If you have any comments or suggestions, please let me know.

This is the first 3-D model I have built from scratch and I was looking to get it done quickly. So, I kept it simple but did note that it wouldn't take much to add a few more amenities that would suit personal needs or desires. The router fits...

PLA will end up sagging, and failing over time.All of these parts are oriented in the correct printing position aside from re-centering the models.No supports are needed. *The cable chain end links printed fine with NO SUPPORT in all 30 different...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

To this end please be sure to down load the most up to date model files before you start printing as things may have changed. Slider Updates include 1) Processor upgraded from RF-Nano to much more capable ESP32 2) The Nextion display is no...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

A short bridge is required for the rail end caps. Post-Printing All holes are intentionally modeled as very tight fits and are intended to be drilled out with a 3mm bit to ensure proper fit. The threaded inserts will push waste material into the...

I had no trouble pulling the mold off the lettering.For creating the CAD model, here are the basic steps I used :Create a “slab” large enough to contain the desired lettering, with additional space fora removal tabCreate raised lettering on the slab...

All overhangs should be 45 degrees or less. Rafts: Not required, unless you experience adhesion issues. License The "Hard Drive Holder" models (.stl) are licensed under the CC BY license by Code and Make. The "Hard Drive Holder" code (.scad) is...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

I can upload the design files for the other models too if there is interest. Please share your creations if you remix. : ) Update 7/16/2020 - The original inner joiner STL was undersized. I have added a new STL ("hexcell_joiner_inner_FIXED.stl")...

And get your supports in order first, the models need a relatively precise and flat supported surfaces. <font size="3">The modification uses many parts from the original setup, but the PTFE tube must be cut, making this a non-reversable mod...

The assembly requires some M4 bolts and nuts, RGB strips, a hot glue gun, and tubing with a external diameter below 13mm (I have used 11mm). If you have any feedback, issues, or suggestions for future improvements please comment in the comment...

...March 23rd - Created a smaller prototype mockup for the bottom, mid and top tray using measurements from the full sized model. Experiencing corner lift on the middle tray, even with brims and the lid/bottom of the middle tray is about 1mm too short.

[Medium Sized Model - 25mm Base] [Presupported in 32mm & 75mm scale]   A Ranger from Nan Thalias. Ervion was sent as part of an Elven diplomat’s escort, alongside his father which was attacked by a retinue of goblins and bandits near the County...