axm paper model

Modified the vent slots on the right side so they are less likely to cause problems during print. I really liked the compact ATX benchtop PS by gdoniu93 and started out simply to recreate the model in Fusion360. Somewhere along the way (as it often...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

* Test your work again * replace the toothpick with the mounting pins * improve the models and share your changes with the rest of us! The difference between this and the original is that I have add a version of the body which has an opening...

I propose a modification of the original model to be able to use clear plastic plates. Thus it is possible to see the interior of the enclosure. The screw fixing makes it possible to make the enclosure completely removable. ## Materials...

Although the chinese version is much cheaper, be warned that some models lack the reverse polarity protection feature from the original, even if they claim otherwise on the backside. Also, some clones have a different layout with non-centered power...

First, I had to model the front of the display to accommodate the RepRap Discount Full Graphics Smart Controller and then I also decided it needed a back to protect the circuit board. Done... Then I decided to tackle the problem of mounting a...

My girlfriend and I both need extras to be placed at our bed, (though slightly dimmer)So all in all, this turned out to be one of my best projects yet! A huge success!Future upgrades:I'd probably switch the Trinket to an ATTiny85 for a more low power...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_extra_port_corner_resolution = 8 custom_bottom_fillet_radius = 1.6 custom_left_port_corner_resolution = 8...

(If all you need is the 1/5 scale dummy engine you can still get his version there.) If you wish to get just my 1/5.5 scale engine remix without the cowl, it is available here: https://cults3d.com/en/3d-model/gadget/carl-goldberg-cub-dummy-engine I...

If you leave about half millimeter extra on each side, you can melt that extra with a soldering iron, so you get a nice finish. To use it in your project you can create a body that connects to the 4 screws in the inner side of the assembly, or you...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 0 stencil_shape = 4 stencil_size = 40 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

This model is designed for pla/pet-g which does not shrink. 2) print in the orientation show in the pictures. While this does not give you 90° opposition for force vs layer lines, it does give you about 45° which is much better than 0° printing with...

About the Models Update: 24th September 2017 Added Y-splitter D6 8th September 2017 Added Multi Material for BLTouch 12 August 2017 Added Multi Material series 11th April 2017 Added Bowden series MM Parts and Y-Splitter I added the new MM parts just...

Attention, there is V2 as when I was designing this I didn't think about some stuff so I added them, but I didn't print this updated model. I'm only unsure about the switch if the top cover will fit as I think it should.</p> <p>Features:<br/> ...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

Note: Scaling down the model too small may not work on all printers. The smaller the part, the more precise your printer should be. 1/2 scale should work well without extra precision. Any smaller will need a printer which supports a step of .05 mm...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 4 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.2 custom_case_wall_thickness = 1.6...

It's now less expensive to build (when building 3+), more water resistant, and offers more space for alternate battery options.https://www.printables.com/model/297089-meshtastic-solar-base-station-node-enclosure-for-3---Build a complete Meshtastic...

Model of the pusher cap and the skirt part used on an On/Off switch combination cast aluminum IP40 case The case with two momentary switches made more than 40 years ago in the GDR (do not call it East Germany, please) works still perfectly fine. It...

OpenSCAD is a script-based modeling software specifically created for projects like this that need to be customizable.If you're new to the program, it may look strange at first, but most of the work is just typing values into a form or selecting...

I made this trap to prevent those pests from killing the bees in my garden if they ever come close. I collected information, examined several models, made by individuals and professionals. This is my version. If you feel it is inspired by something...

Make the adjustments, render the desired  STLs and print it! The models are in the position, they should be printed. No support is needed. ...I suggest to use a 10mm brim for the tube to prevent it from detaching from the buildplate while printing this...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Afterwards, place switches randomly throughout the plate and test that the switches are able to return to their top position once pressed down.If the plate doesn't fit in the case, you may want to trim the outer tabs with flush cutters, or file it...

Depending on the power supply to your printer you may need a step down voltage regulator, pre built versions of which can be found on eBay or Amazon, or you can have a go at deriving a 5V supply yourself with a linear voltage regulator or go all...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...