axial wraith interior 3d models

I have an old Axial Wraith Rock Racer that I set up for FPV with a pan tilt and roll mount. Often even with head tracking and the ptr mount, I can't see as much as I'd like, especially behind me. So this is a set of side mounted mirrors that...

This is a flat skid plate for the Axial Bomber RR10, to adapt a Wraith or other similar 3 gear style trans to the Bomber. Retains original suspension configuration (links front, trailing arms rear). This is designed to retain the front skid plate...

Bumper Reinforcement System Designed to Safeguard SCX10 Style Bumper Connectors Used on the 1.9 Wraith Vehicle.

This is a flat skid plate for the Axial Bomber RR10, to adapt a Wraith or other similar 3 gear style trans to the Bomber. I designed this new version of my skid plate to use aluminum (or carbon) side plates for the upper link mounts instead of the...

... but that's up to the user. This will bolt in where the Wraith Spawn receiver box mounted, and that box will need to be relocated. Uses the original velcro battery straps. ... The holes do not line up with the older Wraith from what I understand.

Front shock mount riser provides additional, and raised, shock mounting locations for the Wraith Spawn. This is another template designed to be printed, then transferred to aluminum other other desired material (.090 6061 aluminum shown in the...

This is nothing special, but I, sharing some spacers I made for my Wraith Spawn. Out of the box, the servo arm hits the bumper under compression. I pushed the bumper out 1.5mm and it clears fine now. The Hood spacers were used to set the...

Axial Wraith Front Bumper Mounts have delivered fantastic performance after thorough testing.

A bed designed to pair seamlessly with Jruutiai's Rear Inner Fenders, or function independently, boasts two distinct variations - a model featuring slots for wire-tying electronics and a solid version.

I Created This Because I Needed a Servo I had purchased the four-wheel steering kit, but it lacked an essential servo motor that was hard to come by in its original form. That's when I resorted to using an unverified replacement, simply because I...

Introduction: This item provides two shapes, round and square to download.Round headlights are diagonally downward by 5 degrees, while square headlights are horizontal.Use ordinary 5mm LED and fix it with a small cover. Need to use M2 * 6 and M3 *...

<p>A bed designed to work with <a href="/jruutiai/about">jruutiai</a>'s <a href="https://www.thingiverse.com/thing:2804455">Rear inner Fenders</a> or stand alone. ...There are 2 versions available: one with slots for wire tying electronics and one that...

This model was designed using Tinkercad. ...Modify it online at https://www.tinkercad.com/things/xWUHFsxwkTz

... lexan body. Requires four M3x10 or 12 to mount the bumper and two M2.5x6 or longer to mount the body. You can see more in my thread on RCCrawler http://www.rccrawler.com/forum/axial-wraith/624894-wraith-1-9-build-rear-bumper-other-mods.html

Snow track kit for axial scx10.1 scx10.2 wraith or bomber. ... They are designed to fit ar44 or ar60 axles only all files and instructions are included You will need -10x m3x16mm screws -2x 1/4-20x2" bolts with locking nuts -152 2-1/2" 8d finish...

The short version matches the original shock mounts as they come from Axial. The tall version works if you flip the rear shock mounts upside down, which raises the shock mount by ~10mm and lowers the rear of the car. ... May require longer hardware...

This is a Fuel Cell for the Axial Wraith that I designed in Fusion 360. It is scaled to fit perfectly in this Trunk made by XEROXCZ: https://www.thingiverse.com/thing:3157008 The bottom of the fuel cell has a slight bevel on one edge to go over...

This is a Fuel Cell for the Axial Wraith that I designed in Fusion 360. It is scaled to fit perfectly in this Trunk made by XEROXCZ: https://www.thingiverse.com/thing:3157008 The bottom of the fuel cell has a slight bevel on one edge to go over...

I needed a custom mount for the RC4WD 9.5cti 1/10 winch to fit in front of the Axial Wraith, but unfortunately, the winch was slightly too large and tall to fit under the support struts. So I designed this little adapter to let me mount the winch...

This was designed to make accessing the Axial Wraith 1.9 receiver box easier. If you've used the BP Customs chassis brace the access to the screws holding the (stock) lid on is blocked and to gain access the brace need to be taken off or loose. ...

However, there's always the standard lexan interior that comes with your Wraith - but let's be real, does it really live up to expectations? To solve this problem, I've come up with a custom interior that perfectly complements the steel outer cage...

Use this adapters with your standard Wraith 12mm Hex and mount the Tamiya Clodbuster wheels to your truck :)

Plug in those adapters with your trusty Wraith 12mm Hex and attach the rugged Tamiya Clodbuster wheels securely to your off-road vehicle.

I designed this so you can tow a trailer behind your wraith 1.9 with a 6mm hitch. Fast and poorly made and may need to be sanded down a bit to have flush edges. After the first print I will update this and report how it went. ... (it might work on...

Below are the recommended print settings: Printer Brand: Ultimaker Printer Model: Ultimaker Original Raft Settings: Rafts: No Support Settings: Supports: Yes Infill Density: Infill: 20% Design Overview My Design Process I started by scanning my...

Printer Specifications: Ultimaker Printer Brand: Ultimaker Printer Model: Ultimaker Original Raft Options: None Selected Support Structures: Yes Infill Percentage: 20% Design Process: To create this eerie design, I began by scanning my Wraiths hood...

Interior for Axial SCX24

Wraith monster for DnD

this is wraith