axial scx10 skid plate 3d models
215360 3d models found related to axial scx10 skid plate.thingiverse
This is a skid plate engineered specifically for the Axial SCX10, boasting a flat bottom and precision-drilled screw holes with counter-bores for maximum clearance and an optimized pocket cutout to minimize weight and printing time. The design...
prusaprinters
This is a skid plate designed for the Axial SCX10. It has a flat bottom and counter sunk screws for high clearance and a pocket cut out for lighter weight and less filament/time when printed. Screw holes and counter-bores are according to M3x0.5mm...
thingiverse
Purchased an Axial Cherokee body for my Scx10 Gen I, but unfortunately, the original skids no longer fit properly. ...To resolve this issue, I decided to combine them with LUBOSH's inner fenders (available on Thingiverse as thing #3206130).
thingiverse
The standard mid plate / chassis plate / motor mount / skid plate (whatever you wish to call it!) has the mounting holes for the axial gearbox which has narrower mounts inboard compared to outboard. The Scout's gearbox holes are square in pattern,...
cults3d
Make your SCX10 more scale by addining this component . This piece is mounted in the chassis. ... You can add a rope to the part that rotates (red component).
thingiverse
This is a skid remix created to fit an Axial SCX10 transmission onto the ECX G1 barrage. The transmission with motor was cheaper to purchase than the actual ECX upgrade G2 Motor Plate and 390 motor. I had to elevate the transmission slightly so it...
thingiverse
I wasn't satisfied with the battery's placement on my Axial SCX10 Deadbolt, so I designed a plate to move it to the back of the transmission. This adjustment sets the battery perpendicular to the body and slightly lower than its original position,...
thingiverse
This is a skidplate/cover for the Chassis mount for Steering Servo SCX10 Chassis by MrCadillacsts https://www.thingiverse.com/thing:839483
thingiverse
... that are not needed. I would suggest using 1 middle mount hole per side to fix the side plates to the skid, and mount the skid plate to the chassis (through the side plates) using the other 3 screws per side. ... If you have any questions, LMK
thingiverse
Update 03/16/17: Uploaded reworked design, making clearance adjustments around link mounts and lowering transmission mount into skid for increased interior clearance. Other cutouts were made for motor and transmission parts due to this change. Note...
prusaprinters
The lower upper link mounting position should keep stock geometry, the upper upper link mounting position should give you a little bit of link rise and keep your pinion angle the same.The link slots have been designed for Revo rod ends, which have...
cults3d
conversion skid pan and link mount for 1:12-14 Thunder tiger kaiser xs chassis to run industry standard 3 gear transmission made popular by axial scx10's and ax10's etc tilts transmission for lowest possible cog without reducing ground clearance may...
thingiverse
Center skid plate for the Axial SCX10 RC crawler, designed to provide a little more ground clearance and prevent getting hung up. This skid plate does affect link geometry slightly. There are two versions available, one for stock links using Axial...
cults3d
Center skid plate for the Axial SCX10 RC crawler. This gives you a little more ground clearance to prevent getting hung up. This skid plate DOES affect link geometry slightly. There are 2 version, once for the stock links using Axial brand ball...
prusaprinters
Center skid plate for the Axial SCX10 RC crawler. This gives you a little more ground clearance to prevent getting hung up. This skid plate DOES affect link geometry slightly. There are 2 version, once for the stock links using Axial brand ball ends,...
thingiverse
i designed it for my jeep probly works on outer scx10 builds 154.60 long (the middle bar has some end corve) x 57.22 (from the skid plate to the top of the bar thingy) ** added new branded bumpers ** ** new barned for all offroad porducts "bratso off...
thingiverse
Skid Plates for TFL aluminum axles. ... The plates are designed to bolt into the existing M3 threaded holes that are in the TFL axles (Srews M3 x 6mm).
cults3d
ARMOR PLATE FOR BOTH SIDES AND REAR GLADIATOR WORDINGS BEST TO PRINT IN PETG ALL USES M2X6MM NUTS FOR THE REAR PARTS CAN CHANGE THE FILAMENT INTO WHITE IN CURA POST-PROCESSING SETTING
thingiverse
Skid for the axial capra using a wraith or scx10 transmission and has mount on the skid for 3s 1500mah lipo battery.. ive used twin hammers lower trailing arms with great success with this skid im sure you can use whatever link combo you can fit. ...let...
cults3d
Axial SCX10 2 Steering servo plate on the axle
thingiverse
nearly identical to the GSpeed one just slightly different edging.
thingiverse
The Axial SCX10 III is a great truck, but the inner fenders have holes for optional rock lights. I do not use those lights and I wanted to seal the holes so I created this rock light block off plate. ... Each plate requires (2) M2.5x6mm flat head...
thingiverse
... SX107 servo and also replaced my DIY linkage with the servo saver that came with the Capra kit. This was when I realized that a cutout is needed in my mounting plate. See file "axial_capra_skid_raised_mounting_plate_DIG_servo_saver_cutout" ...
pinshape
Axle-mounted SCX10 2 steering servo assembly
myminifactory
It's specifically engineered for an original SCX10 model, however, the fitment may vary on the II version due to its unique specifications. I haven't personally tested it on an II model since I don't have one available. ...Apologies are in order for any...
thingiverse
I designed this skid plate to swap all the parts from my Redcat e-10 buggy into an Axial Capra cage. The "Redcap" parts are drawn with the Redcat transmission pattern. For an Axial style trans, use the SCX10 labeled part. The upper link mounts...
thingiverse
Flat skid-plate whit big motor compatible (like 2400kv 1415 castle) no need for more screw
thingiverse
Muffler for the axial scx10-3 Jeep Gladiator. ... Designed to use the original screws.
pinshape
I designed this bottom plate as a cradle for utilizing a two-speed transmission from a Traxxas Summit in an Axial SCX10. This version is specifically tailored for use with the Axial OEM U-frame. Notably, the mount for the shifting servo requires some...