axial scx10 body 3d models

I am making 8x8 RC with SCX10 axles so I needed two "pass-thru" axles. When using two same axle housing halves, you loose two pillars for mounting servo plate. I made a 4-link truss that integrates servo mounting pillars too. I recommend not to screw...

This is my version of a durable lower control arm for the Axial SCX10. You just need 108mm M3 threaded rod and two of the original ball joints. Axial provided two different lengths of control arms. 114mm short wheel base (Dingo) and 121mm long...

... ... They are specifically designed to be mounted directly onto the Axial SCX10 frame rails, offering a flexible installation process that can be adapted by leaving them intact or trimming them at the notched section to achieve shorter overhangs.

These are bumper brackets for the Axial SCX10. Made these so that I could extend both the front and back to fit a new body. Also added stabilizers to use towards the battery holder as I had to move mine to the front. The battery holders will have to...

I needed a bit more room underneath my SCX10 body. The stock side skirts were mounted too high and didn't seal the body well enough. So I came up with a design that adds three plates on each side, which now fit perfectly under the body. They provide...

I've designed axial SCX10 2 Cherokee inner wheel wells to keep mud from entering the bodyshell. I created them using PLA, but a flexible material would be better, especially if you could switch materials and print the back support out of PLA or ABS...

Fits the side rails plastic part of the Axial SCX10-3 crawler. I decided that one of the domes has to be chopped off, which is not a big deal, as the sliders may still be fitted with the same screw from underneath into the ESC support. Dimensions...

This is a DIY rod end for Axial SCX10 or Capra I suggest printing them one at a time to avoid stringing and to minimize surface imperfection as much as possible because the fit is very tight. You may need a hammer to insert the ball into the rod but...

These are rock sliders that can be installed on the Axial SCX10 iii Basecamp.I printed these from Prusament PLA as a prototype and have yet to break them.  If they break, I plan to use some Prusament PC blend CF.You will need two M3x10 and two M3x6...

...... They are engineered for seamless integration onto the Axial SCX10 frame rails, offering the flexibility to adjust their length by either leaving them in their full form or carefully trimming them at the notched section to achieve shorter overhangs.

Servo saver 25t for mini servo of scx10.3.

** This is a snow plow designed specifically for the Axial SCX10.II (SCX10.2) Unimog UMG10. ** *** In theory, this should bolt directly onto any SCX10.II axle and frame, but you may need to add some shims or washers to secure the upper frame mount...

This is a skid remix created to fit an Axial SCX10 transmission onto the ECX G1 barrage. The transmission with motor was cheaper to purchase than the actual ECX upgrade G2 Motor Plate and 390 motor. I had to elevate the transmission slightly so it...

This is a skid plate engineered specifically for the Axial SCX10, boasting a flat bottom and precision-drilled screw holes with counter-bores for maximum clearance and an optimized pocket cutout to minimize weight and printing time. The design...

... them and it seams to work fine. You will need to get Axial Slipper pads AX31068, or you can print the one I included in PetG or TPU but I can't guarantee it will hold up long. ... This is a remix from https://www.thingiverse.com/thing:398515

rock slider remixed for scx10 ii build to share with everyone

Mounting plate for SCX10 transmission to mount 2 motor for more power at low speed

This is a closed narrow box for rc-receivers, to fit the right side-panel of the Axial SCX10-3 crawler. It provides 2 cable outlets (end and inner side). The goal was to replace the original and relatively huge Axial receiver box, so scale- builders...

This is a skid plate designed for the Axial SCX10. It has a flat bottom and counter sunk screws for high clearance and a pocket cut out for lighter weight and less filament/time when printed. Screw holes and counter-bores are according to M3x0.5mm...

People typically use axial 1.9 bead-lock wheels for off-road purposes.

... the outer holes on the stock shock hoops. This lift kit may fit other SCX10 models depending on shock position and geometry. Lift kit tabs are 4mm thick, identical in size to the stock spacer. ...To install, simply remove the stock spacer.

I design a scale, off road, front bumper for my Axial Scx 10 I. Happy with the result. Easy to print. ... Strong and durable even in PLA+.

SCX10 Front Mount Low CG Battery Tray. Strategically relocates battery weight directly over the front axles, dramatically improving vehicle balance. Engineered to handle oversized 5000mah batteries while minimizing zero binding...

SCX10 Center Side Mount ESC Tray Designed For Stock ESC, May Fit Others. Dimensions Are Optimized For Seamless Installation. To Secure The Tray In Place, We Recommend Using Longer 3x12mm (AXA436) Self-Tapping Screws That Will Provide A Rock-Solid...

... needs. With my extensive collection of vehicles, including an SCX10, RC10B3, SCT410.3, Tamiya Hilux, Losi 5ive-T, Savage, and RC10T (aluminum pan), I have a wealth of resources at my disposal to create unique parts or serve as dimension references.

I wanted a stealthy front bumper for my SCX10.2 XJ, so I took matters into my own hands and created one from scratch. The first attempt was made with the front facing upwards in the printer bed, but unfortunately, it didn't turn out as well as I had...

Below is the list of hardware required for this modification: - SCX10 II aluminum servo mount (you can find a good deal on Amazon); - M3 or M4 threaded rod (I opted for 4mm since I couldn't locate the 3mm option); - Rod ends (the included ones in...

So, I created a one-piece flip mount/back bumper with room for the stock 5mm LEDs and a trailer hook from Wish (Practical Simulated Trailer Hook For 1:10 SCX10 90046 Traxxas TRX4 Climbing Crawler). My local customers praised it, saying things like...

I recognized that V1 only accommodated battery packs of the same size as mine, so this updated part places your SCX10's battery over the front axle and suits all chassis types. The first component fits above the bumper struts, while the second...

simple armor rock sliders, glue or bolt these on body