aw11 mr2 c pillar trim 3d models

C PILLAR TRIM UPPER

The owner of this vehicle is a proud enthusiast who drives a sleek and agile 1985 Toyota MR2 AW11 that proudly showcases its original factory design, including a bold red paint job and distinctive pop-up headlights.

Toyota Mr2 Aw11 Badge that is mounted on the front of the car. Comes in a 1:1 ratio (altough not perfect). P.S it does not come with the 3 mounting clips as its intended for universal usage. ... Have fun :D

Mark 1 MR2

This is a scanned reproduction of one of the headlight eyebrows for the Toyota MR2 mk1. The original piece that I copied is made of TPU and it didn't want to hold quite the right shape during scanning, so the curve of this reproduction isn't...

This is a basic adapter designed specifically to fit into the radio slot of an AW11 model Toyota MR2. ...Simply print out this component and secure it firmly in place using a strong epoxy adhesive.

I'll delete the antenna on your Toyota AW11 MR2 with this plate. The design works for the 1986 MKI-A chassis, but I'm not sure about the B chassis. ... I created this plate in Fusion360 and tested it on my own 1986 Toyota MR2.

I crafted a custom keychain featuring the iconic AW11 MR2 logo, which I had previously 3D printed with iron PLA approximately twelve months prior. It has remained securely attached to my keyring during that entire period. ...The design was created using...

This is an emblem I made for the intercooler cover on my AW11 Toyota MR2. ...Heat from the engine has not been an issue because this part of the intercooler cover is sealed from the engine bay and, through the grille, is exposed to outside air.

Coolant Reservoir Cap for 4AGE Toyota MR2 AW11 MK1 non-supercharged. These Caps are hard to find these days. Here you only need your oem tubes and a 2mm rubber plate which you have to cut to a ~40,5mm diameter. I use my one (high temp resin print)...

Enhanced Aerodynamic Cap Design for Toyota MR2 W1 Model - Larger and More Streamlined

My MR2 was missing the sticker on its intercooler, so I designed and printed one. I printed it out of normal PLA because I am not too concerned with engine heat. I consider this part of the intercooler cover to be outside of the engine bay...

The intermediate shaft of the steering column on AW11 MR2s was designed as two pieces that are held together by a rubber bushing. After 30+ years (or in my case a quick ratio steering rack install) the rubber bushing disintegrates and you are left...

Window bracket to Mount Slider Text Case in Toyota MR2 Aw11 rear Window. ... Two Snapper and one original mounting screw of the interior trim.

Clutch Alignment Tool for a 1989 Toyota MR2 AW11. Really just a 21mm cylinder, same diameter for the hole in the Flywheel as the ID of the clutch spline. If it prints undersized, scotch tape is about 0.1mm, works great to size it up. ... I could be...

This is a precision-engineered ring crafted specifically to bolster the dimmer wheel on an AW11 MR2 headlight switch assembly. Notorious for their tendency to crack, these delicate components are prone to damage over time. ...This ring expertly fits...

This is an almost completely accurate model of the front hood prop clip for the 1984 - 1989 MR2.

Part; T-top SUNSHADE latch pieces.Application; Toyota MR2, AW11 body style.Versions; two versions1) Individual OEM parts (if some of your original parts are usable)2) Modified, all printed parts (if your latch is gone or totally broken)Notes; ASA...

This is the flippable cupholder for the Toyota MR2 Mark1 Armrest. Diameter to fit Standart 500ml cans and bottles (~66mm] No drilling or glueing needed! You need - 4mm round aluminium profile / rod for the hinge - 2x small Screw (s.th. ...like M3x10)

This was designed to go together with my other model for the radio mounting brackets with my radio that I have in my MR2. If you have a different radio and/or use different mounting brackets, then download the model without the radio hole and put...

This is a cover for the seatbelt bolt, where the seatbelt attaches to the B pillar. It has enough clearance for the seatbelt anchor to move freely. ...I attached mine using 3M VHB double sided adhesive tape and it seems to hold well enough.

I'm working on designing this replacement plate in the center console of the MR2 Mk1 that tends to wear out. I've printed this, but I haven't installed it in my car yet. ...I'm printing this on my Elegoo Mars in black, then hitting the high spots with...

... Please do not use the "Tip Designer" feature if possible. If removing that button is feasible, please let me know how it can be done. This part was originally known as the A-pillar cover, which is what I've called this item from the start.

I've been working on a new line of upgraded models that I'm really excited about, and I have to say, they're looking better than ever compared to their predecessors. ...I plan to keep pushing forward with these updates for quite some time.

Prototype bracket designed for mounting a Haper's Hatch to the MK1 MR2, AW11 chassis. Untested. V2 model features a narrower width of 50mm as opposed to 100mm. Also, the angle has been adjusted to 29.5° from its original 30° setting. Unproven. The...

Inlet flange for 4AGE Toyota MR2 supercharger

Inlet flange for 4AGE Toyota MR2 supercharger

I was looking for a way to hold my phone securely inside my MR2 so I decided to take matters into my own hands. I utilized the clip designed by bcruton and added a base to it that can friction fit snugly between the radio and shift console of my...

Replacement headlight and wiper knobs I designed for my MR2 - printed them out of black PETG with 0.4mm nozzle and 0.2 layer height. I have been running them for 2 years now without issue except very slight warping due to heat. May need to shim the...

These plates are designed to mount a BOSS 625UAB to the center console radio hole of my 1985 Toyota MR2. My car did not come with any sort of radio in the hole, and there were just a bunch of loose wires and 4 holes that would hold up the mounting...