automatic trash can lid 3d models

here is an updated version of the lid for the "Muelleimer/ Desk trash can" (under trash can). It holds on tighter to the trash can with out falling off. hope it works for you. ... It will need supports.

These are replacement hinges to replace some that broke on an automatic open/close garbage can. I cracked off the hinge stubs using pliers and shaved down to a flat surface with a razer. The replacement hinges have a hole for hinge pin which was...

This trash can lid clip requires 4 small screws. ...This was designed to fit a very specific model of wheeled can ([link here](https://www.lowes.com/pd/Toter-48-Gallon-Brownstone-Plastic-Wheeled-Trash-Can-with-Lid/1000345689))

I'm replacing the busted hinges on my automatic garbage can with new ones, taking care not to damage any surrounding parts. To get started, I carefully pry off the old hinge stubs using pliers, then smooth out the surface area with a razor blade. The...

I made a lid for my brute trash can https://www.thingiverse.com/thing:5321517. ...It can be printed without supports.

This is a lid I designed to go on top of my brute trash can model found here. ...https://www.printables.com/model/151879-brute-trash-can-pen-holder .It is designed to be printed without supports.

I designed a lid for our kitchen trash cans. Our trash cans have a size (outside) of 22 x 39.5cm (20 liters). The system is the "separato M" from Nobilia. Printing takes quite a long time, so please check the dimensions from the sketch beforehand....

My city provides large trash cans for garbage, recycling, and yard waste. One of the pieces that secures the lid to the body broke, which made the lid dangle annoyingly whenever it was opened. Since the city doesn't offer parts, I instead copied the...

I saw a trash lock design by tymbo13 but I couldn't get my trash can lid to be secured properly so I did a remix of that design and here are the list 1. Remix bolt hole by relocating and using M8 hex bolt and nut 2. Remix arm by adding a slot 3. ...It...

Basically I needed to make a lid for that wonderful trash can to keep my cats out. I made a small version for used hobby blades and other sharp/dangerous items so they couldn't later become toys. ...Its scaled to the original size of the model, so tweak...

Basically I needed to make a lid for that wonderful trash can to keep my cats out. I made a small version for used hobby blades and other sharp/dangerous items so they couldn't later become toys. ...Its scaled to the original size of the model, so tweak...

Basically I needed to make a lid for that wonderful trash can to keep my cats out. I made a small version for used hobby blades and other sharp/dangerous items so they couldn't later become toys. Its scaled to the original size of the model, so tweak...

It is made to turn a Cafe Bustelo coffee grounds can into a trash can. Thought Im sure it could fit on more things that are also a 4in diameter and could be scaled to fit others if desired. The print is made of two parts and very easy to...

For printing instructions, use these settings: _partGap = 0.08, _lipHeight = 2, _minimumWallThickness = 1.0, _part = lid, _resolution = 60, _style = round, _insideDiameter = 13, _bayonetDepth = 0.4, _numberOfSides = 9, _topBottomThickness = 1.0, and...

... file(see photo for supports I used). I printed this in PETG for it's flexibility so the tabs can flex during install(and if you need to remove it); abs or pla may also work but haven't been tested. The walls are pretty thin so print it solid. ...

trash can pin for lid

I constructed a trash can.

My trash can lid latch broke and I couldn't find a better fix or an existing replacement part, so I broke out my calipers and designed a beefed-up replacement that should outlast the original.

Replacement battery cover for my amazon basics automatic trash can. The original kept falling off into the can and batteries along with them. I designed one with a bit tighter clearances so it's a little more snug. Been holding up for months now. ...

Ninestars Touchless Automatic Trash Can (version that takes 3x C batteries). Mine fell into the trash and got thrown out, so I made a replacement (for 3D print ever). I based it on one generated by TheHeadlessSourceMan's Battery Cover Creator, but...

This is a replacement battery cover for the Ninestars Touchless Automatic Trash Can, 50L / 13.2 gal., which uses three C batteries. Mine fell into the trash, but fortunately, it was recovered in time to serve as a model for creating a new one using...

... printer for filament scrap disposal etc. ...The lid is designed to be hinged using magnets so it can be removed and a liner used without falling off. ...If you don't want to or have a magnet, you can also use a small piece of filament as a hinge piece.

  A beautiful trash can suitable for your home, office and especially bathroom. Compared to its size it uses little material and is very sturdy. The container can be used with or without the print-in-place swing lid. ...Included versions: the Body with...

Simple design to fix the broken hinge of my kitchen trash can. ...It's my first design 3D design!

Included versions: A: Regular Body_regular: The body with a height of 230 mm (default) and a thickness of 0.8 mm Body_regular_lower: The body with a height of 210 mm and a thickness of 0.8 mm Body_regular_thicker: The body with a height of 230 mm...

When the word "filthy" popped into my head, I couldn't help but envision a trash can, so I set out to create one. ...The result is a fun little desktop toy that's perfect for stashing cards, candy, and yes, even trash.\r\n\r\n*This model was inspired by...

As soon as I associated the term "filthy" with something gross, a trash can sprang to mind, prompting me to build one. It turns out to be a great little desktop toy ideal for concealing cards, candies and even trash. ...This design originated from an...

I printed the trash can for compost by desk and after one day there was a lot of moisture. Came up with this design using some charcoal filter to allow moisture out and hopefully keep the smell down. ...Uses 4 m3x12mm screws</p> <h3>Print...

When the word "filthy" pops into my head, a rusty old garbage can instantly appears, inspiring me to create a miniature replica. This quirky desktop companion is perfect for concealing cards, candies, or even actual trash. ...I based this design on an...

Easy print. ...No supports needed.About 10.6cm in width. 11.8cm in height without lid and 12.8 with lid.