autodesk inventor 3d models

Also, my printed model needs some clean-up on the outer edges of the ducts (which you can see I did not do). You may have better results with your printer. Printing & Assembly notes: Save the 2 self-tapping case screws when you disassemble the...

Refer to the pin diagram below.Connect the SMPS OUT- to a ground pin on the RPi.If you're using the fan, install it on the lid.Connect the fan's power and ground wires to pins on the RPi. My 5v fan was a little on the loud side so I used 3.3v and...

... If this is the case, and accuracy is important, you should scale up the dimensions a little bit to compensate. I only tested this for small gaskets. If the model proves unpractical for larger gaskets, contact me and I'll see how I can improve it.

Required hardwareRaspberry Pi Pico (RP2040) microcontroller boardUSB cable (as it has to be cut and soldered a USB 2.0 is preferred, because it only has 4 wires)4x Cherry MX key switches or other with similar size4x Keycaps (or print your own)4x M2x6...

Trim/Cut plastic flowers from a dollar store. Modified from this model: https://www.thingiverse.com/thing:3666273 Photo frame with a sliding/rotating cover. Slightly recessed oval of 40mm wide by 55mm tall to attach a 2D printed image/photo. Three to...

Most issues with these printers can be traced back to this strain gauge probe not functioning properly.It would be convenient if their mainboards were compatible with the CR-touch / BL-touch probe style sensors found on the newest higher end Creality...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

What's IncludedThe entire Anvil Digital Forge Patreon release for January 2024, including; Multi-Shell Options:A number of STLs are labled with "(Multi Shell)" - these files can be imported into Blender (reccomended), or Meshmixer, or various other...

Make your design on whatever modeling software (or download your design). Export as stl.</p><figure class="image image-style-align-center image_resized" style="width:40.37%;"><img...

These are modelled from the original Type-R parts. (I reinforced these as much as possible). What you need? - Complete RB6 rear mount transmission and motor mount. (Transmission case that comes with the spare part set numbered UM508C.) - About...

... cut methodology used. All credit for the idea to use them as puzzles goes to Quadratum Cubicum (QuCub.com - no author name noted) and this was already licensed under Creative Commons Attributable before I modeled the pieces and the base/lid. ...

He shipped back a huge quantity of Parian marble to use for his ethnographic portraits of Greeks, especially for portraits of the peoples of Paros, and eventually realizing at least twenty-seven busts, medallions and full scale figures representing...

Because of the simple geometry of the Box and the Pieces, these modest settings produce a very nice model in a relatively short print time. Please Note: Although I have not provided the solution here, I will respond to personal Thingiverse messages...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

My prototype box had a problem in which the combination could be guessed by feel due to the slack in the model. This problem was fixed with a number of features that make guessing the combination by feel very difficult. As an additional precaution, I...

I added a switch at the bottom of the right arm (super easy access).To fix the led support, you will need 2 M5x12 screws (Original, it bottom 8mm long, they are little short, you will need 12mm minimum, if it is longer, it is not annoying)I haven't...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

This update is not just about keeping your Raspberry Pi 5 cool; it's about giving you the freedom to personalize your setup like never before.Introducing the GeeekPi ICE Tower Cooler for Raspberry Pi 5: Elevate your setup with this impressive cooler,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

My prototype box had a problem in which the combination could be guessed by feel due to the slack in the model. This problem was fixed with a number of features that make guessing the combination by feel very difficult. As an additional precaution, I...

Except for the Sunlu mount plate just lay the models flat. The Sunlu mount plate I printed standing upright - even without support (although some minor bridging is needed, but that was no problem)</p><p>As mentioned above, the hygrometers are...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 48...

Basic profile: 25% infill, 4 walls, ironing top layers, ...Note: the included images illustrate the goals of the steps outlined below.[ ] 3D Print included stl files[ ] sunlu_fan_mount.stl -- Mounts 50mm blower fan and thermistor to rear of fan...

3D Printing: The Morse writer telegraph consists of many printed parts that are assembled together. Some of them could have been printed as a single piece. However, I avoided doing so to keep the printing times manageable. Additionally, this allows...

:D This is a "small" and simple attempt to build a 3d printer. Small and simple are the keywords here. Just some basic parts to print, standard components you can get anywhere and no special and expensive tools required, as I don´t have access to a...

**HOW I PRINT MUCH QUICKER WITH STOCK HARDWARE** -------------------------------------------------------------------------------------- Here are the two videos that give details on how I print much faster with stock hardware (changes to slicer...

My goal was to make as many of the modifications as possible to be 3D printed parts.Note that in addition to the .STL files, the Fusion 360 file containing all these parts is also provided. Some parts need to be rotated after importing into the...

NewsMarch 20, 2022 added bigger hookMarch 21, 2022 added USB flash drive holderMarch 21, 2022 added hooks (12mm and 25mm, screwed with M3 screw)March 21, 2022 added box (screwed with M4x10 screw)March 21, 2022 added 2 wall parts (224x190 and...

When I saw the Safe box from Hugo this inspired me to do my own Safe (or Lock).This is not a remix. I modeled everything in CAD from the scratch. But i printed Hugo's version before and &nbsp;had a look at it. I recognized parts which he designed...

&nbsp;If you also made this mistake (or if you like the look of the colour-matched annotation labels), I have uploaded those “caps” in the model file “Fix for Rotated Board.zip”Print each label with the dimensions 185mm x 12mm x 4.78mm. (You may need...