audio interface desk mount 3d models

quick model of microphone arm desk mount should fit most IKEA desks without any issues. ... test print out of PLA came out great, fits perfectly snug use with caution, no clamp, no warranty Materials needed: 2x M3 screw 8-22mm long 2x M3 nut 1x...

Remixed design of the original double stream deck desk clamp (https://www.thingiverse.com/thing:3969782) by adding a cylinder modifier for a cable hole.Frame can be mounted either way to have it either above or below desk level. ...You will need three...

I decided I'd rather have more desk space so I designed some brackets to be able to mount the laptop under my desk(sit/stand). I made sure to leave some open space in the bracket for my power supply. ... I also made sure to have holes so you can get a...

Created a 2 piece mount to keep my laptop out of the way when using at my desk. It is attached to the leg of my VariDesk standing desk. The laptop this was designed around was ~21mm thick and fits quite well. This part is set up to use 4 M3...

This is a desk mount for the Fiio K5 Pro, this model can be used for both regular desks and desks with frames underneath (up to 25mm).All that is required is to screw into the bottom of the desk and slide in the K5 (you may need to take off the feet)...

This is a remake of Tanacota's Desk Mount Headphone Holder. ... https://www.thingiverse.com/thing:2732522 I simply eliminated the cable support, speeding up printing and saving material.

I wanted to clear up some desk space, so I made a mount to place my Grace SDAC and O2 amp underneath it. I was able to print this without supports.

This is a remix of the desk mount by phatbeetz that features the HOTAS tray which can be printed in 2 parts making in suitable for smaller printers with heights from 240mm +.

Desk mount trash box Table up to : 20 mm, 30 mm,  40 mm or 50 mm (form IKEA Lack Table)2 depths : 40 mm or 70 mm(screw_v2 is a little smaller to fit well the holder)

Under Desk Laptop Mount Dimensions Internal height - 38mm Internal depth - 234mm Hole Dimensions Screw hole - 3mm (countersunk 6mm) Pass through hole - 6mm (Use the scale tool in your slicer to adjust the width/height to fit your desired laptop)

A remixed version of Beaver's headphone holder which allows for mounting underneath a desk, rather than on the side, giving a cleaner look.The clamp gap is 30mm.

I've Designed a Clever Desk-Side Headset Holder, Expertly Managing the Lengthy Cables of My Trusty Hyper-X Cloud 2 Headset with Ease, While Providing a Rock-Solid and Convenient Mount for the Control Box Right at My Fingertips.

I designed a Desk-Side Headset Holder that expertly manages the lengthy cables of the Hyper-X Cloud 2 headset, providing a safe and highly convenient mounting system for the control box.

I wanted to mount my powerstips under my desk. If the two outer sockets are plugged with a Schuko-plug, the powerstip holds itself in place. ... Otherwise you might add an additional screw as seen in the picture.

The new IKEA Alex desk is great, it looks sleek and offers some clever cable management solutions but unfortunately there was no way to mount my beloved desk lamp. So I created this part. This part is mounted to the wall next to my desk and I can...

If you enjoyed this project, and you want to say "Thank you" please consider supporting me by sending a tip on thingiverse or my PayPal here. Under-desk Laptop Mount Simple under desk laptop mount. Print in default position. ... - Maximum laptop...

This is a bracket I made to hold a volume control unit from my PC speaker system, allowing me to mount it underneath my desk. This fits the Logitech Z313 Speaker System, specifically the round volume control unit. The round hole is for driving the...

... To attach the Gamepad to the mount, I used two strips of Velcro - one on the Gamepad itself and another strip on the mount that sticks to the desk in the middle of the fork. ...The second strip was optional, but it gives a more secure hold.

Designed in fusion 360 a mount to hold my razer ripsaw under my desk. Once mounted you will have to unmount inorder to remove the ripsaw. Cables have tones of space to fit in including the front mic and aux I/O. ...The holes for mounting are fairly...

By placing it under the edge of my desk, I was able to keep my workspace clutter-free while still having easy access to the volume control or being able to switch to using speakers. This design uses the factory screw locations on top for the case...

I also didn't wanted to mount them flush inside the desk, so I designed these mounts which replace the original sidecaps. The L-Clamp takes an M4 Nut and gets fastened by an M4 (i used an M4x30) Screw through the replacement sidecaps. ... The...

The center bracket with three holes is securely fastened to the underside of the desk right against its central support, giving just the right amount of space for slipping the laptop between the side mounts. The gap between these side mounts varies...

Remixed Nivier51's Nerf Disruptor mount to include the screw clamp from the popular Headphone Desk Mount. This allows me to mount the Nerf gun to the side of a desk securely. There is a normal version, which uses the full size of the screw clamp...

The HOLA desks are based on parts of kaidi electronics, so I guess this mount will fit more desks. My chair hit the display a couple of times, so the bracket broke out. Since my service engineer was not available, I decided to print one. So if...

Simple hdmi under desk / side mount, remixed the one from TomHammond since i didn't want to drill a hole to flush mount it. ... Beware that it fits very tight around the switch, you might want to scale it up just a little bit if your printer is not...

This is a remix for the PS5 controller of this followings things : - https://www.thingiverse.com/thing:2076034 - "Desk Mount Headphone Holder" - mistertech - https://www.thingiverse.com/thing:4668997 - "PS5 Controller Wall Mount" - Stridershouse You...

Couldn't find a suitable bracket to screw to the underside of my desk that would give a horizontal mount for the Modular Mounting System so made one. Its my first attempt at altering something but seems to have turned out well. ... I have included a...

... https://www.thingiverse.com/thing:4885570. ... The mount was changed to mount to my desk and the arm was shortened. Thanks for the original. Please think about buying me a coffee. ... https://paypal.me/rob180sx3D?country.x=CA&locale.x=en_US

Under desk mount for your headset/headphonesMounting holes are 5.25mmHollowed out section for running you wire through, to keep it out of the way.Printed with 15% infillPrint on side for no supports

I designed this because most headphone mounts here at Thingiverse were to small for my desk, and the ones that did fit were too wasteful. This mount with its clamp will fit any table from 45 mm to 15 mm thick. I'm currently using it to hold my...