atx support 3d models

PC ATX low power lab power supply.Printing without support in 0.20 or 0.15For the screws:4x M3 of 5mm4x 20mm wood6x m24x molded nutsElectronic part:Voltage Regulator :...

The PSU project is one of the many find on internet, personally i followed the @tartaglia project (thanks) and i added some modification.Pay attention that the fan cut is based on my PSU that has the fan on the rightRegardsJonwebUpdated...

Specifically, the one used is from here: http://www.ebay.ca/itm/221826130907?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT or search for 24Pins ATX Benchtop Power Board Computer Power Supply Breakout Adapter. Print Settings: Rafts:...

Electrical Setup I'm not going to reinvent the wheel here, as there are tons of instructions online for converting an ATX PSU into a general-purpose one. Check out WikiHow's guide if you need more detail. Here's my quick cheat sheet on wire colors...

A Tight Right-Angle Fit for Modern ATX Power Supplies Engineers rely on a precise 90-degree angle to house ATX power supplies with ease, as seen in the innovative design showcased at https://www.thingiverse.com/thing:4055781.

Remixed for use with the K8200/3Drag, a high-performance ATX PSU mounting system designed specifically to accommodate 2020 aluminum extrusions. ...The PSU is securely fastened atop the Kossel, allowing optimal airflow through the integrated ATX fan...

This is an ATX power supply cover to build your own laboratory power supply. ... It uses the ATX power supply standard size and you only need some long screws to fix it and some banana connectors.

Benchtop Powersupply case for the DPH32ß5 buck-boost converter. Has mounts for an ATX power supply.

Select Honeycomb Pattern as Fill for ATX Power Supply Void Coverage and Opt for 20% Density Filling

Hole template for micro ATX motherboards. ...Original hole size should be 0.156" but i change holes to 4mm

Base para montar placa adaptadora ATX, requiere: - 4 tornillos m3x8mm - 4 tornillos para fuente de poder (opcional)

Transformer une vieille alimentation ATX en alimentation réglable 0-30 grâce à un module buck-boost trouvable facilement sur internet

I replaced my faulty ATX PSU with a reliable one to avoid the inconvenience caused by my previous Chinese-made unit. The design of the left bracket still requires confirmation for optimal cable output configuration. Update: adjustments made to the...

I used ABS for sturdiness and heat resistance.ElectronicsI followed the DroneBot Workshop setup.PartsHercules ATX power supplyhttp://athenapower.com/node/191#USB panel flush mount connectorhttps://www.amazon.com/gp/product/B073HXLKTLTerminal blocks...

To convert your own computer ATX power supply into a lab power supply, follow these steps: http://www.wikihow.com/Convert-a-Computer-ATX-Power-Supply-to-a-Lab-Power-Supply I added two amp meters, each connected to a ground plug, so I can measure the...

... power leads (rear lip), but it still fits OK. Had to rotate the model 45 degrees to get it to fit on a 20x20cm build platform (just fits). Print Settings Printer: Anet A8 Rafts: No Supports: Yes Resolution: 0.2mm Infill: 10% Category: Electronics

You can screw the bracket from the inside on a table or something more heavy. I bought the board on Aliexpress:...

Changed the size of the holes to accommodate individual 4mm banana plug sockets Wanted to have up to 30v @ 150w so crammed the buck boost into the ATX power supply case and wired that to the DPS 5005 BOM: * DPS5005 * 4mm Banana Plug Socket *...

I borrowed some PC elements such as PSU (Yang Ji of USA), Graphics Card (Ted Barrett of Australia), and a full Micro ATX motherboard (philippe cavalier of France) for illustration from GrabCAD library. ...Thanks to those peoples who gave me such...

A computer case that can use a Micro ATX motherboard.If your 3D printer can print 330mm*330mm area, you can print it happily!

XH-M299 or the PCB breakout board for the ATX power supply converts the ATX power supply into a cheap bench power supply, but the PCB breakout is bare and quite hazardous to work with without proper handling and isolation. Most maker's tables are...

A Laboratory Power Supply Created by Upcycling a PC's ATX Power Source This project utilizes a power source from an old PC, specifically one that uses the ATX (Advanced Technology eXtended) standard. ...The following parts are required: * An old PC's...

Hello there! ... I have designed a fast to print ATX power supply mount, im new in 3D design, but done my best!

adding an M-ATX to NR200 computer case 2 x top 1 x bottom left 1 x bottom center I found that printing it sideways yielded better results

A 17-inch by 9-inch American Racing ATX 195 wheel features a 5 on 5.5-inch lug pattern and has a backspacing of 4.53 inches.

Unplug your ATX power supply and grab a cable comb to tidy up its 24-pin connector - it's time to get organized!

Intel Mini ATX Motherboard. 170mm x 170mm. 85% populated against original design. Used for a client we were desiging a secure server housing. ...Image rendered using PV360

I rely on my trusty ATX PSU as a reliable laboratory power source, so it's been securely fastened beneath the work surface using two sturdy screws.

I utilize an ATX PSU as a laboratory-grade power supply, thus it's secured underneath the workbench using two screws for added stability.

A copy of the ATX specification for PC components. ...Hosting here to allow access for those wishing to construct their own cases and use in modding projects.