atx motherboard mounting plate 3d models

An ATX motherboard is a type of main printed circuit board in a computer that adheres to the Advanced Technology eXtended (ATX) form factor standard, which defines its shape, size, and layout. ...This form factor is widely used in modern desktop...

This was created to support a PCIe x4 splitter for an ATX motherboard with seven slots. I've also included a four slot bracket. ... These work well with https://www.thingiverse.com/thing:4789196 due to the 4mm thickness of the bracket.

... might be more practical to insert them one by one at an angle based on your print bed size. Print the "Complete" model or: - 2 Longs & 1 Short The holes are not pre-threaded, yet they are precision-made to accommodate standard motherboard screws.

The original mATX Motherboard Tray design by skywurz on Thingiverse needed some tweaking to get it just right. The issue was that when sliced with Cura, the tray came out too narrow - a mere 9mm wide. ...To fix this, I remade the design from scratch to...

This is a board for mounting creality 4.2.2 and 4.2.7 motherboards and compatible PCBs as well as the Raspberry pi 4. I was inspired by the voron switchwire to make this board. The one of the voron SW superimposed the 2 boards one on the other and...

Micro ATX motherboard stand, with hard drive slot under motherboard wood mounting with 4 mm screws fixing the motherboard on the bracket with dedicated screws

Simple ATX computer motherboard port cover

Stand for ATX motherboard to assemble with 4 M3 screws and nuts.The model has been cut to be printable on MK2 and MK3.Then the stand can be fixed with wood screws to a board. ...Be careful, the screws must not touch the motherboard. 4x M3x10 or...

My ATX motherboard cable was a little too short, so I made this spacer to push the PSU further into the case. ... The thickness is 25mm, because this was the difference between PSU screws, and the fan screws I used for mounting this.

Cut down in size for printing multiple pieces on any 220mm x 220mm printer, I noticed Thingiverse lacked micro ATX mobo trays suitable for smaller printers. This design prints perfectly on an Ender 3, taking nearly 9 hours to complete. The tray...

I based this revised design on my previous one, which allowed me to install my motherboard upright within a wooden enclosure (http://david-moody.info/woodworkingadventures/?p=1420). ...This updated model is more robust and features precise hole...

A bracket designed to mount an ATX power supply to the underside of a bench/table/any other surface. Designed to work with #8 wood screws. ...

I this to test GPU's. This new version has the power supply underneath to save desk space. YouTube Channel https://www.youtube.com/channel/UCZ8WG-kqF1kmL2s0xIMfIIg If you found this video helpful or would like help fund future...

This plate adapts the hole pattern in the cargo bay of an iRobot create to mount a mini-itx motherboard inside.

(I personally had this happen to me.) So, I designed a buffer plate to print and place as a "buffer" between the motherboard and the frame. If you look closely at the motherboard picture, you can see on the left side the red buffer plate. ...The third...

This Thing will allow you to CLEANLY mount an AT or ATX PC power supply inside the case of the original power supply that was inside your Amiga 2000. I have no idea if all AT/ATX power supply boards are the same size, but in any case this Thing is...

You're working with a straightforward SFX-ATX Adapter Plate. Possibly you'll need to fine-tune the holes for your intended application. Be cautious, as an extra grounding wire may be necessary between your power supply and case! ... Print Settings...

The motherboard templates were created by user "venounan" on Reddit and are being provided here for easier access at https://www.reddit.com/r/pcmods/comments/1chkph/i_made_an_atx_motherboard_mount_template_would/. I am not responsible for any...

Use these brackets to mount an HP Erica3/5 motherboard in a standard ATX case. Use one screw on the top left motherboard hole and mount three of these brackets on the bottom 3 holes of the case. ...Motherboard will side into the slot on the brackets

This Mac G5 modification will utilize various components to enhance its performance and features.

These brackets are designed for mounting an ATX motherboard in a Powermac G5 case without damaging the existing mounting pegs. A Fusion360 project can be downloaded here: http://a360.co/2GfSDiA You can discuss this build on tonymacx86 at...

Recently I needed to recover from the bottom of my electronics stuff and old days ATX Lab Psu made many years back in the days before I came to the 3d printing world. So I decided it deserved a new face and a second life span. Many of the mod...

So I created some simple parts to help with mounting the motherboard, expansion cards, ATX power supply and hard drive. I also borrowed a handle from https://www.thingiverse.com/thing:4702410, with some modification so it could be used on 2040...

I printed this on my MM2 with full support

<p>The reason for multiple pieces is because my printer is a Prusa Mini.</p><p>&nbsp;</p>

The MM2 printer was utilized to produce the item, featuring complete support during the printing process.

A Gigabyte X570 AORUS ELITE AM4 ATX motherboard texture and ready to go for small Price !!! ...too:) hope you enjoy

Designed for a standard motherboard standoff to press firmly into place, providing proper threads for installing the motherboard screws easily. This allows users to attach their motherboard to any surface that can be screwed into - wood, plastic, or...

I was searching for a reliable ATX I/O shield compatible with my HP Pavilion motherboard and decided to create one myself instead of relying on external sources.

Mounting bracket designed to secure strap across top of ATX power supply as shown in provided image.\r\n\r\nNOTE: The image above is used solely for reference purposes and does not belong to me, all credit goes to the original photographer. ...This...