atomrc swordfish 3d models

Some of the parts I used in my AtomRC Dolphin build, as seen here https://youtu.be/_WoeBPlrSDc

Uses the canopy screws, probably works on all the Atomrc planes (I guess they got same screws)Print in Tpu.

Aerodynamic and torque resistant motor mount for the Atomrc Dolphin. No support required. ...A regular motor mount plate and 4 M3x30 screws required

Replacement for the wooden base plate in the rear compartment of AtomRC Dolphin with two 30.5x30.5mm mounting places. I've printed using PETG. ...Fusion360 model included.

Reference scans from AtomRC Dolphin. Note that the front canopy has been modified to maximise airflow through the front section of the aircraft. ... Produced by https://www.thingiverse.com/brogers123/designs using Einscan SE scanner by...

Rear landing skis made for the AtomRC KillerWhale. Tested in the snow and improved upon to this version. Reinforced to not snap in the cold. ... Please print at 100% size and with supports

This is the AtomRC Dolphin vertical stabilizer For the Left stabilizer just mirror it in Cura. ... Designed for LW-PLA with infill 0% - total weight 9g PLA version will be around 20g+

Canopy for AtomRC Dolphin plane Designed in 2 parts top and bottom for supportless print I personally eSUN LW-PLA with 3% infill, 2 bottom layers Contains a hole for the DJI Vista antenna.

Front Landing Ski for the AtomRC killer whale. Made after several versions the top is made to meet with a servo + horn. It is reinforced as to not break in the cold. ... Please print with supports PRINT AT 75% SIZE

The SX-2 Swordfish from the 1950's comic "The adventures of Blake and Mortimer".

The archive contains Swordfish Bills' files from 2011, including FBX format and textures.

Swordfish: Ship of the classic anime cowboy bebop and upcoming Netflix live action adaptation

AtomRC Dolphin esc plate. ...Print with no top layers or bottom layers to use your infill as ventilation Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 200 Infill: 38 Filament: PolyMaker PETG Category:...

Remixed this to fit the Runcam5 Orange with the TV-Out cable installed in the nose of the AtomRC Dolphin. Because of the TV-Out, an FPV camera is not needed. ... The tab on top is used with the stud and a 3mm thread insert to screw through the camera...

AtomRC Dolphin esc plate. ...Print with no top layers or bottom layers to use your infill as ventilation Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 200 Infill: 38 Filament: PolyMaker PETG Category:...

I got a AtomRC dolphin with a 1700kv ES2306 motor with a german 7042 prop. I put this values into ecalc and figured out, that on 4S the temperature of the ESC could rise to an unhealthy level. ...So I designed this air inlet for the ESC.

Make a simple stand for Swordfish II. Not perfect but it holds up. ... https://www.thingiverse.com/thing:4521280

Fascinating Swordfish When you see a swordfish in the sea, you watch with amazement and admiration, why do you expect to see only at sea, thanks to this Metal Wall Decor you can see this wonderful fish in your home or office at any moment. ...In ancient...

Hello everybody, I design some parts for AtomRC Dolphin. Flying with a single camera mount https://www.youtube.com/watch?v=0Q9CI8qhfBU Nose parts: Install the holder in the foam, I used 3 screws to join the nose with the holder. ...

I built a holder specifically designed for my Swordfish II model, and it could also be used effectively for storing golf balls.

When you attach it to your backpack or keys, the swordfish's presence is unmistakable, a bold statement that exudes confidence and strength. ...Whether you're heading out on an adventure or simply running errands, this swordfish keychain is sure to turn...

This is a base/stand that I made in tinkercad to support the excellent Swordfish II model found here: https://www.thingiverse.com/thing:4521280

After a crash with my AtomRC Seal, the latch that secures the hatch was nowhere to be found, so I modeled up this little replacement. you need: M3 threaded rod cut around 35mm. I cut down an M3 bolt I had 1x M3 nut1x 7/32"x11/16" compression spring...

... stress on the servo. But you can also just use steel push rods. the whole from wheel assembly then gets glued in the spot. the origilan plywood plate is not needed here. https://www.prusaprinters.org/prints/77803-landinggear-atomrc-killer-whale

... ----------------------------------------------------------------------------------------------------------------- The Swordfish of Blake & Mortimer available on Thingiverse! ...Featuring a base, it makes for a nice little decoration for your desk!

the origilan plywood plate is not needed here. https://www.prusaprinters.org/prints/77219-landinggear-atomrc-killer-whale Print Settings Printer Brand: Prusa Printer: i3 MK3 MMU 2Rafts: No Supports: YesResolution: 0.2 Infill: 20% Filament: PLA...

https://www.prusaprinters.org/prints/77219-landinggear-atomrc-killer-whale Print Settings Printer Brand: Prusa Printer: i3 MK3 MMU 2Rafts: No Supports: YesResolution: 0.2 Infill: 20% Filament: PLA PLA Notes: PLA parts: 0.2mm Layer; 2 outer shells; 4...

Atomrc Dolphin elevonThree different types:Plane elevon,  you need to glue in servo horn andduct tape elevon to main part of the wingplane elevon with place for connectors to the wing (use 16mmx28mm)With place for horns and connectors (see...

The spaceship "Swordfish II" is a sleek and advanced vessel that serves as the main mode of transportation for the crew of Spike Spiegel and his team, a group of bounty hunters on the run.

Stand for Swordfish 2, I utilize the arm of ddany1st from Thingiverse. The URL is https://www.thingiverse.com/thing:3289793/files. ... There are two distinct models: Logo oriented at thirty degrees Logo oriented at forty-five degrees