atomrc f405 3d models

The ESC is secured using two cable ties in all versions, while the VTX is glued down on the F405 and 30x30 plates and cable tied on the F722/F405 version. The F722/F405 are identical and represent the latest iteration, making them by far the best...

As above, mount for action 2 to dolphin fpv wingE: today while flying was 32 Celcius and my dji action 2 overheated- designed more cooling version2 options:to print with TPUto print with polilite pla and install camera in tpu insert.Print settings...

Stock style mounting for 19x19 motor mounting.

Needed a nano mount for the Dolphin and didn't love the options that already existed. This one fits the HDZero Nano cam well, I expect it should fit other 14x14 cams as well. The only trimming required is the opening for the wiring on the wing...

just a quick remix to add some venting to allow air flow.

Маунт состоит из 2х частей: первую часть нужно напечатать из твердого пластика (предпочтительнее пла+). Вкладышь из мягкого пластика (ТПУ, Флекс и др). Вкладышь удерживает камеру и закрепляется двумя винтами м2 размера. Вентиляционное отверстие...

Better and more aerodynamic elevons! These elevons are recommended if you desire a more efficient or fast flight. The two-part elevons are fasten together using a 4mmx1mm x225mm and a smaller 4mmx1mmx20mm carbon-fiber rods. ... Material: use...

A strong and light canopy for the Dodo, as the original ones tend to break in no time. This one frames the camera and vtx antenna to keep them safe. ...I use a stripped foxxeer lollipop 3 and fits perfectly safe behind the shark tail.

I lost my rear hatch in a crash, so I designed this as a replacement. It should be a pretty nice fit, but if anyone has any major issues, reach out and send me a picture and I may be able to do some further tweaking. There are two versions. ...I made...

A blue 270 degree servo is used to rotate the camera. On the turntable (mid.stl) you need to glue a double rocking chair from the servo to which the serva itself will be attached. --------------------------- Для вращения камеры используется...

With this piece you can put a runcam 5 or similar in the area for gopro, you must cut the cork a little and remove the piece of wood that is at the bottom and replace it with the "camera cover" piece

After some test flighting with the nose of the first model ( https://www.thingiverse.com/thing:5365305 ) This is an improvement to prevent breaking the nose in landings. The top of the nose is PLA the bottom is TPU. ... Notice: Single camera:...

Twin motor pods for the Atom RC dolphin. You need longer 3mm bolts for the motor, and a 35-40mm bolt to hold the mount to the pod. Glue these to the wing, I glued mine 50mm from the inner root of the wing, centered on the holes. The two holes on the...

... To accommodate this, I designed a part that lowers the shelf by 10mm to fit modern flight controllers fully installed. Specific decks for F405-WING, F722-WING, and F765-WING are available, along with a universal deck for other flight controllers.

This is a modified version of K1nk0's F405-Wing FC mount that I've tailored to accommodate M3 bolts in the base. To secure this to the balsa wood in the Binary, I used wingnuts. I thickened the base and enlarged the holes so the bolt heads fit...

This project was crafted using Tinkercad's intuitive interface. ...To make modifications, simply click on this link: https://www.tinkercad.com/things/lrsAPiwpAOH edit it online.

Hide all your cables underneath this cover to give a neat look with full access to usb port Watch a review of my AR Pro Mods here: https://www.youtube.com/watch?v=U8NLCYz1H8Q

This is a remix from GizFPV's excellent HeeWing T1 Ranger Parts listing and the All-in-one FC/VTX/GPS mount part. ...I needed just the flight controller base and thus trimmed the elevated structure for VTX/GPS away.

I was unhappy that the top of this otherwise excellent flight controller has exposed power terminals. I decided to design and print a cover that would cover the battery and ESC terminals and give a bit of protection to the micro SD Card as well. The...

I made this two-part FC tray for the Finwing / Xuwing Albabird. Use the lower part as a guide, to ensure the tray sits and glues nice and level. Once the glue sets, you can slide the lower part out. Or, you could glue both in place for extra...

Removed the screw handles on the sides for more cleaner look when using double sided tape to mount the plate. ... Used web-tinkercad

Atomrc Dolphin support for Runcam Thumb and 19x19 Caddx Ratel 2 The 2 magnetics are the original 10x2 Used ABS without supports

Atomrc Dolphin support for Runcam Thumb and 19x19 Caddx Ratel 2 - The 2 magnetics are the original 10x2 Used ABS without supports

This is a model of the atomrc penguin's plastic nose that screws on to the front. You can print one in any color to accent your aircraft, or to replace a broken one. I also include a mod for a matek digital airspeed sensor pitot mount. I include the...

DJI Action2 mount with optional nd filter

Use M2 or M3 screw for the hood holder and M3 srew for cord holder

One degree motor adapter for dolphin. Tpu. Mount such that it's notch down. ...Print with PETG.

I made this mount to suspend the VTX to allow more air around it for cooling. In conjunction with a NACA duct in the nose, this has worked great for preventing overheating without requiring a fan, as well as easy access for maintenance. M3 screws...

Dolphin DJI 03 VTX Plate for front of fuselage. ...(2mmx15mm screws to mount into wood)

I use Liitokala HG2 http://alii.pub/6145rs Flight with this battery's https://youtu.be/srlGr4DGuwg