atomic fillament 3d models

This creation was expertly crafted using Tinkercad's intuitive design tools.

The holder is designed to securely hold the filament in place above the 3D printer.

Skate Kugerllager benötigt (608ZZ)

Attach the printed spool to your REPRAP by placing it on top and securing it with nuts (hopefully added during construction) on the upper threaded bars. Despite appearing wobbly in the photo, this setup is surprisingly stable. The design works...

Having tried several other filament rollers, I wanted something simple which could use the existing Creality stock holder as a base that didn't require any extra hardware. I created several different designs with FreeCAD before settling on this one....

Resolution: 0.1 - 0.4 Infill Density: 50 - 100% Recommended for Anet A2, A2 Plus, Ender 3, Creality CR10 and Printers with a 2020 Profile Long Version Length: 250mm Short Version Length: 210mm Disclaimer: I Have Not Tested This Yet

Printed on the stock BIQU B1 My first design on Fusion 360 but after a couple versions it came out perfect for me. Extra materials: 6000 bearing M3 x15cm screw V2: made a small mod to the original design to prevent it from moving. ...

책상이나 선반 아래에 붙여 최대 2개의 필라멘트를 거치할 수 있는 행거입니다. 2개 또는 4개의 나사로 고정하며 짧은 드라이버가 있어야 합니다. 서포트는 필요치 않으며 인필은 최소 50%로 채워야 튼튼합니다. 날개 옆의 구멍에 미사용 필라멘트를 끼워 두세요. A hanger that can be attached under a desk or shelf to hold up to two filaments. It is secured...

This is an adapter for the CR-10 that lets you attach the roller holder to the top profile of the printer.

Sehr praktischer Organizer für kleinere Sachen die sonst einfach nur in der Gegend oder in kleinen Tütchen rum fliegen. Die 2 Zentrierungen benötigen leider ein wenig Support Die Bohrhilfe einfach deckungsgleich über 1 der vorhandenen Löcher...

This creation was designed using a digital fabrication tool called Tinkercad and has been thoroughly evaluated.

Kindly try it out and report back!

This design was inspired directly from thing:805717 and incorporates some notable modifications to ensure the filament guide tube does not move excessively downward. Depending on your assembly setup, it may be necessary to trim your filament guide...

I've built a straightforward hanger that keeps my filaments neatly arranged and accessible right next to my reliable DaVinci 3D printer.

This is a small tape applicator I created to make applying Kapton tape to ABS parts with minimal filament remaining easier. It was also an opportunity for me to practice designing something in Solidworks. Inspired by the Kapton Killer, designed by...

If extended cylinders can subsequently be employed for dual revolutions, then smaller units are able to cast bearing cones with, or without, internal bearings on an uncomplicated machine base that facilitates effortless turning.

tray that hold 20 samples 96.9 x 81.6 x 21.3Fillament sample by FuniverseMN https://www.printables.com/model/509317-filament-sample-cards

Filament guide for MK3s in LACK enclosure. The filaments are located on the lower floor of the enclosure. ... The idea is based on the Minimal PTFE Tube Guide @matthew, which is, however, too rigid for free movement of the filament from the coil below.

Test passed successfully!

Here is a filament reel designed to fit nearly all sizes of those troublesome inner diameter filament reels. The holder utilizes two skateboard bearings inserted into the bottom holder cone and then placed over the 7mm hub pin. For optimal tension...

Simple filament holder for wall. Required parts: 1x printed holder base (screwed securely into the wall) 2x printed holder sides (firmly gripping spool from both sides) 3x screws to mount base firmly onto the wall 2x 608 bearings, used in...

Out of filament and stores are closed? No problem! Just crank out more! ...Print with whatever material is on hand, no need for supports - simply wind it onto a new spool as it flows out of the extruder.

Purchasing the As Built board was a smart decision, because carefully reviewing it helped me understand that the published documents including actual sizes didn't line up perfectly with my board, ensuring those planning custom cases will appreciate...

Easy to print, funky penpot for budding science folk

This thing was crafted with Tinkercad. ...Edit it directly on line at https://www.tinkercad.com/things/xVzEoH9Fw4Y

We've crafted an engaging and one-of-a-kind dice to elevate your board game collection. We're thrilled you'll have a blast with it! ...If you appreciate our unique designs, consider showing your support by liking our Facebook page.

***Preview: https://youtu.be/oTkFhUcJyHY For any questions, issues send messages

Twins. ...Pretty twins.

A Customized Version of http://www.thingiverse.com/thing:548191 is Here! Created with a Special App - Customizer! You can find it at http://www.thingiverse.com/apps/customizer/run?thing_id=548191. **Instructions** Use These...