atlas lathe dro 3d models

This is my version of a tailstock DRO bracket for the PM-1236T lathe, using an iGaging scale. I 3D printed the bracket in PLA, using an infill of 100%. The top half of the iGaging scale slide bracket is re-used to clamp the slide to the tailstock...

So I've been getting back into using my Chinese-made Harbor Freight Mini-Lathe, which is featured here: http://diy3dtech.com/mini-lathes/, and wanted to add a Y Axis DRO to it without breaking the bank. I designed one of my own using an affordable...

Lathe Bed Caliper DRO I designed this item because I did not like the back lash in the feed knob. I wanted to know how far I was cutting exactly. My solution was to brainstormed mounting one of my calipers on the bed then I could 0 it and know that I...

So I have been getting back into using my Chinese made Harbor Freight Mini-Lathe (see more here: http://diy3dtech.com/mini-lathes/) and wanted to add a Y Axis DRO (Digital Read Out) to it but didn't want to spend big bucks so designed up one of my...

So I've been getting back into using my Chinese-made Harbor Freight Mini-Lathe and wanted to add a DRO but didn't want to spend big bucks. Instead, I designed one of my own using an economical dial indicator that I got off Amazon and extended the...

I was eager to fit a DRO onto my lathe tailstock. Found some designs within Thingiverse but they didn't exactly meet my needs, so I designed this very basic version. The mini lathe is a 7x14, a very common Chinese type of lathe, which was supplied by...

My Simple DRO Variant for Small Lathe Tailstock Using Affordable Chinese Caliper Bill of Materials: * A caliper like this one can be purchased on Aliexpress: https://www.aliexpress.com/item/150mm-6-Plastic-Dial-Caliper-high-quality/473639151.html * 1...

So I have been getting back into using my Chinese made Harbor Freight Mini-Lathe (see more here: http://diy3dtech.com/mini-lathes/) and wanted to add a DRO (Digital Read Out) to it but didn't want to spend big bucks so designed up one of my own using...

So I have been getting back into using my Chinese made Harbor Freight Mini-Lathe (see more here: http://diy3dtech.com/mini-lathes/) and wanted to add a DRO (Digital Read Out) to it but didn't want to spend big bucks so designed up one of my own using...

So I've been getting back into using my Chinese-made Harbor Freight Mini-Lathe and wanted to add a Y Axis DRO but didn't want to spend big bucks, so designed one of my own using an economical dial indicator from Amazon. If you need to extend the...

The Dro Panel for Lathe Machine.

This dongle allows to use a high precision indicator with your mini lathe. Maximum useful measure radius is 26mm plus-minus 0.5mm. It also allows to check the cross slide drive mechanism wear and alignment. Indicator wall had been designed to...

The components have been reconstructed by analyzing a real Atlas Mk.2 Lathe, but the precision might not be perfect as it depends on the original lathe's draft angles. ...The majority of the cross slide and compound slide specifications have been...

A faulty traverse gear case in my antiquated Atlas 10-inch lathe prompted me to search for a reliable blueprint; unfortunately, none were satisfactory. Thus, I reverse engineered the existing one, with an aluminum build planned - steel is possible,...

Revamped gears, particularly tumbler and change gears, are designed for the Atlas 10" lathe. The gears boast a 20-degree pitch angle, with the 60-tooth gear having undergone redesign on September 26th, 2013. If you've downloaded an older version,...

Atlas 10F gears, 9-48a, 9-48b & 9-190 for reverse gear assembly Yet to be printed and tested! ... Now printed, fettled & installed, all working well

This is a genuine reproduction of the original drive pulley used on the Craftsman/Atlas 1/2 drive motor shaft, offering precise compatibility and reliable performance.

Needed wiper covers for the lathe I was rebuilding and drew these in Sketchup. Sketchup file along with the stl provided. ...

No modifications to the lathe are required and the only fastener used is a 3.5" 1/4 20 bolt with a nylock nut. You may need to drill out the hole where the bolt goes, and don't be afraid to sand it to fit your carriage. Prints well with no support on...

Uses double sided tape thats about 1mm thick when applied. ... You can either use angled (2 part) or straight version.

Disadvantages mounting scale on tail stock side of cross slide: - the gib screws can no longer be adjusted (without removing the scale) unless quite some distance is kept from the cross slide - the tail stock cannot move as close to workpiece...

Vevor Mini Lathe DRO mounting kit (YS-2260A).The "Apron.STL" that I used for modelling the parts is from https://www.thingiverse.com/tonycstechOn a small lathe it is very hard to find an acceptable mounting spot for the x-axis scale. I did decide to...

Here's a straightforward, quick, non-destructive way to use an inexpensive digital caliper from Harbor Freight ($20) to make a functional (x axis) DRO for a Variable speed Central Machinery 7x10 mini lathe in under 3 minutes without altering anything...

Acme crossfeed nut specifically designed for use on Atlas and Craftsman six-inch lathes.

This is a replacement handwheel designed to fit an antique 1935 Craftsman/Atlas lathe, complete with a comprehensive knurling library crafted by a skilled individual elsewhere.

... for a setscrew, but it fits so snugly on my lathe that I didn't need to use the screw. This modification may work on other Atlas/Craftsman 618 Lathes, but it was specifically designed for this model - http://www.lathes.co.uk/atlas6inch/page2.html.

This replacement cover is designed for a vintage Craftsman / Atlas lathe from 1935. It securely attaches to the cross-slide, shielding the threads and providing protection. ...The design has been updated, with modifications made to the .scad file so...

I installed the modifications on my 10F TH54 Atlas lathe according to the original instructions. I also repurposed a component to serve as an indicator for future reference. ...However, I am unsure which other models these adjustments could be...

I am displaying this Atlas metal lathe change gear rack. The idea was to create a designated spot for all the parts that can be removed so none go missing. I printed with 5% infill and it appears sturdy enough. This is my second Fusion 360 project,...

A special batch of nuts is tailored specifically for my Atlas QC54 Lathe. Two distinct files make up this new version: one has a relief feature to prevent band sawing damage, while the other is a revised model that I originally printed and showcased...