ath m50x hinge replacement 3d models

191020 3d models found related to ath m50x hinge replacement.
ATH-M50X Hinge Repair
ATH-M50X Hinge Repair
pinshape

Recommended Print Settings: Material: PLA, PETG, ABS Layer height: under .15mm (My printer does a great job at 0.0875mm) Infill: 30% Also see ATH-M50X Hinge Reinforcement, a free hinge reinforcement for those who want to preemptively protect their...

ATH-M50x hinge delete
ATH-M50x hinge delete
thingiverse

My m50x folding hinge pin kept breaking even after replacing it multiple times on both sides so i decided to just remove it.

ATH M50X Hinge Repair
ATH M50X Hinge Repair
thingiverse

3D printed end stop for the Audio Technica ATH m50X. Its similar to the ones being printed on ebay except with one uses two M3 screws to camp to the headphones. ...They work great and saved my headphones.

ATH-M50X Hinge Reinforcement
ATH-M50X Hinge Reinforcement
pinshape

The hinges, in particular, had become the weakest link - a small plastic tab designed to prevent hyper-extension was on the verge of breaking under constant strain. When it finally snapped for me, I knew I had to act fast. That's when I came up with...

Ath-M50x Hinge Fix / Support
Ath-M50x Hinge Fix / Support
thingiverse

Design was created by the following: https://www.thingiverse.com/thing:3515489 Updated to work with my ATH-M50X. ... Wasn't fitting correctly needed more thickness.

ATH-M50X Hinge fix (pure PLA, no tools required)
ATH-M50X Hinge fix (pure PLA, no tools required)
thingiverse

This is a replacement part for the little nub thing on the ATH M50X that keeps each hinge from hyper-extending. This build requires NO SCREWS, NO GLUE, NO TOOLS, just regular PLA. I've done some varies designs to increase strength of the pieces.

ATH-M40X Replacement Hinge
ATH-M40X Replacement Hinge
thingiverse

Replacement hinge for ATH-M40X. This is the left hinge. I could not find other hinges that were satisfactory for my needs. This is designed to be printed in resin. ...The wire that passes through the hinge needs to be de-soldered from the jack, pulled...

ath-m50x microphone
ath-m50x microphone
thingiverse

Audio Technica ATH-M50x microphone mount fits both the Ath-M50 and possibly other headphones. The mount was secured to the headphones using double-sided tape. The following cables and microphones were used: Cable: A 3.5mm male-to-female aux audio...

ATH-M50(X) Replacement Hinge
ATH-M50(X) Replacement Hinge
thingiverse

I engineered this custom replacement hinge specifically for the Audio Technica ATH-M50, following repeated failures with the original hinge, which snapped apart five separate times despite my best attempts to repair it using glue.

ATH-M50(X) Replacement Hinge
ATH-M50(X) Replacement Hinge
thingiverse

... ...I changed the model for my headphones. Changes: 1. Reduce bar size for 5mm (23.87 -> 18.87) 2. Reduce hinge pins diameter 3. Add flat part to hinge pins 4. ...Fix the list of included files to match the current dev branch of the MCAD library.

Audio-technica ATH-PRO700 replacement hinge
Audio-technica ATH-PRO700 replacement hinge
thingiverse

Replacement hinge for Audio-technica ATH-PRO700 Headphones. ...SLA printed

 Audio-Technica ATH-M40X Replacement Hinge
Audio-Technica ATH-M40X Replacement Hinge
thingiverse

This is a replacement hinge designed for Audio-Technica ATH-M40x headphones. This was a challenging project that required creating multiple prototypes before reaching this final version. **Key Compatibility Features** The new hinge is compatible...

Audio-Technica ATH-M40X Replacement Hinge Connector
Audio-Technica ATH-M40X Replacement Hinge Connector
thingiverse

The connector on Audio Technica ATH-M40X headphones tends to break quickly when used normally, leading to a situation where the speaker section may detach from its metal mount and suffer further damage. I encountered this issue twice with my...

Audio Technica ATH-M40X Headphone hinge replacement
Audio Technica ATH-M40X Headphone hinge replacement
thingiverse

Replacement part designed for Audio Technica ATH-M40X headphones that might also work on other similar headphones like M50s (I haven't tested this). If you ask me, I would be willing to make a few small changes to the design if it's just widening a...

ATH-M50x Headphone Lapel Mic Mount
ATH-M50x Headphone Lapel Mic Mount
thingiverse

This is a mount for attaching a lapel mic to a pair of ATH-M50x headphones for speaking to people over the interwebz. It slips over the cable and left ear cup and has a hole for a 12AWG wire to stick out and hold a mic in front of your mouth. It's...

Headphone Hook for ATH-M50x with Cable Hook
Headphone Hook for ATH-M50x with Cable Hook
thingiverse

Hook for Audio Technica ATH-M50x headphones that also includes a hook for cables. The top hook matches the width of the headband of the ATH-M50xs. ...The backing was designed for use with 2 medium sized command strips and can be put anywhere you can...

ATH-M50 Hinge fix
ATH-M50 Hinge fix
thingiverse

ATH-M50 Hinge fixA simple headphone fix that allows you to change not the entire headband, but only a small part. ...-suitable for models:ATH-M50ATH-M50xATH-M50xbtATH-M50xbt2

Ath-m50 hinge fix
Ath-m50 hinge fix
thingiverse

This is a gift for individuals who own a 3D printer and an ATH-M50 with a broken hinge, allowing them to print a replacement as a preventive measure against future damage. All the original movement has been preserved. You can view the details in...

ath m50x suspension strap mod
ath m50x suspension strap mod
thingiverse

print 2, one for each side. Then I used a cut up sock as the strap itself but you can use whatever fabric you want as long as its not too thick. ... Good luck

Audio-technica ath-m30x hinge top replacement
Audio-technica ath-m30x hinge top replacement
thingiverse

my m30x broke so i designed this.

Audio Technica ATH-M40x Hinge
Audio Technica ATH-M40x Hinge
thingiverse

This is a replacement part for Audio Technica ATH-M40x headphones. I believe from around 2016, yours may differ. Mine already has a longer metal band in the hinge like here: https://imgur.com/a/BT9mG . If you like it, consider a small donation...

ATH - M50 Hinge Nub Fix
ATH - M50 Hinge Nub Fix
thingiverse

The crucial piece holding back my ATH-M50 earpiece from rotating too far forward snapped off and vanished. I checked out alternative repair methods, but many involved disassembling the headsets or drilling into them. I sought a rapid solution that...

Audio-Technica ATH-M50X Earcup Expanders V3
Audio-Technica ATH-M50X Earcup Expanders V3
thingiverse

Earcups are too close for my ears, and it gets painful to listen for a long time, so I made a solution for us to use. The design is symmetric for both earcups. Took me 3 tries to find out the best way to print this, 2nd picture shows the best way I...

Audio technica ATH-M50x headphones PBR
Audio technica ATH-M50x headphones PBR
sketchfab

3ds max 2011 model. ... Two versions: low with diffuse map and subdivided with vray materials PBR Version Included Four PBR textures pack - Unity 5 Standart Specular - Unreal Engine 4 - PBR Metal-Rough - Vray -link removed- -link removed- -link...

Audio Technica ATH-M30x M50x Headband
Audio Technica ATH-M30x M50x Headband
prusaprinters

<p>I just wanted to make my M30x immortal so yeah</p><p>I tried printing this out of a bunch of different filaments but I found that PETG is the best material for it.</p><p>So far I tried random PLA+s, ABS+s and PETGs</p><p>Most PLA+ lasts around a...

Audio-Technica ATH-M40X Replacement Hinge Connector: thicc edition
Audio-Technica ATH-M40X Replacement Hinge Connector: thicc edition
thingiverse

A custom-made variant of the original design is available, engineered specifically to work seamlessly with extrusion printers and accommodating 5mm cable ties. ...For optimal outcomes, printing on one side yields superior results.

Audio-Technica ATH-M40X hinge (left & right)
Audio-Technica ATH-M40X hinge (left & right)
prusaprinters

Hinge for the Audio-Technica ATH-M40x. I tried out the version from thingiverse (<a href="https://www.thingiverse.com/thing:2823187">https://www.thingiverse.com/thing:2823187</a> ), but I thought it didn't fit well so I recreated one myself.</p><p>I...

Audio Technica ATH-M40X left hinge
Audio Technica ATH-M40X left hinge
thingiverse

The left hinge part for Audio Technica ATH-M40X headphones takes shape in Tinkercad, marking the second iteration of the design. This refined version boasts an improved fit and incorporates strategically placed stoppers to prevent the earcup from...

Audio Technica ATH-AD 300 replacement float
Audio Technica ATH-AD 300 replacement float
thingiverse

This is a replacement part for Audio Technica ATH-AD 300 headphone float part.

Audio Technica ATH-SR50BT Headband Cover Replacement
Audio Technica ATH-SR50BT Headband Cover Replacement
thingiverse

I couldn't find the original part anymore to glue it back together or something so I designed a replacement in FreeCAD. A nice side effect is you can use some fancy colour to make the sr50bt more appealing (sadly my cool pink filament wasn't able...