atem mini rack mount 3d models

The mini rack is for 4 standard 10ml vape juice bottles. ...Two of the bottles is placed with bottom down and two with bottom up for collecting the juice at the tip (emptying).</p><p>Fast printing at 0.2mm layer height, 2 bottom and 3 top layer with...

Mini Rack for doll, plush or cat clothing. It is adjustable in height as well as length. 2 versions of the legs with adjustable height via small wedges: minimum height of 150mm and maximum height of 200mm, minimum height of 200mm and maximum height...

This is a two piece rack for holding mini pliers. ...The needle nose plier is about 4.5 inches long.</p> <p>I was able to press the cylinders into the holes of the end piece without requiring glue.</p> <h3>Print Settings</h3>...

I have a couple of Mac Mini's running VMs and Docker containers that live in a cupboard and run quite hot when simply stacked on top of each other. To address this issue, I designed a snap-together rack allowing air to flow freely between them. The...

Miniature rack for use with a UniFi USG, 60W 8 port switch, cloud key, and patch panel

I needed a usb and hdmi cable guide behind my Atem Switcher and this is what I came up with.

A compact 5x5 Eppendorf tube rack designed to securely hold and organize standard 1.5 mL tubes, perfect for laboratory settings.

This rack consists of three pieces: a primary rack, a support leg, and a clip designed specifically for hanging it from our window frame. There is also an alternative version of the clip featuring a hole, which allows users to drill or nail it...

After conducting an online search, I couldn't find much information except for a 3D printed mini rack design shared by a user on Reddit. I used that design as inspiration and completely redesigned the system to fit my specific equipment and 3D...

Here's How You Can Make One: Gather the Following: * Two CDs, stripped of their label on one side * A glue gun or some Double-Sided Tape * A 1/2" Long Threaded Bolt with a 1/4" Diameter or Smaller * A Matching Nut * Optional: two small Washers for...

I designed my own version of a 6” rack enclosure inspired by this one by KronBjorn.I used acrylics which are cut on a CNC as top, bottom and side panels but you could also use 3d printed panels as well.The front plate dimensions are the same with the...

I searched the web and couldn’t find much other than this that a user on reddit came up with. Using that design as my inspiration I totally redesigned it for the specific equipment I am using in my house and 3d printed the parts. I understand the...

MiniDisk - Rack Since I own a ton of MDs without any sleeves or cases around them, I decided to create a rack so they can fit snugly without the sleeves. There are two holes in the back of each one, allowing you to hang them up in multiple ways. If...

MiniDisk - RackSince I own a ton of MD's without any sleeves/cases around it I decided to make a Rack so they can fit in snuggly without the sleeves. There are 2 holes in the back of them so you can hang them up in 2 ways. If you like HoneyCombs I...

The rack features small feet on the bottom and cutouts at the top, allowing them to be stacked easily. Print Settings Printer: MonoPrice Maker Select Rafts: Doesn't Matter Supports: No Infill: 10% Notes: I ran this with no...

To avoid clutter on my desk, I designed a compact rack that accommodates up to twenty CDs or DVDs. However, I find ten disks fit comfortably while still allowing easy insertion and removal without hassle. The dimensions of this untested design are...

Mini Test Tube Holder for Eight 12mm Tubes. Meant to be printed upright, will require supports. Printed with a small brim to help prevent warping. Minor cleaning with pliers, scalpel, or sandpaper is necessary to remove supports and ensure test tube...

I saw other racks like this and wanted to print one for myself. It turns out I have a tiny printer so I had to redesign everything to work with my specific equipment and print bed restrictions. Unless you have this exact same setup, you'll probably...

I built a compact wall-mounted storage unit for my new miniature screwdriver set that I picked up online from Amazon.

A compact and innovative Lazy Susan spice rack designed specifically for the CountertopChallenge. This unique project utilizes two CDs as a revolving mechanism, providing a smooth and quiet rotation experience. To create this clever device, you will...

You want a support for your mini-skates? Stop looking and print this one! The holes allow are just aesthetic and allow a reduction of PLA since it is already very solid! Don't forget to leave a little like and post your impressions so I can see...

We discovered a solution with this cleverly designed mini-portable clothesline ready to print. We used the clothespin designed by Werner Stein (thanks!). You can find it on Thingiverse: http://www.thingiverse.com/thing:609650 Print as a single...

... sleek organizer stores the components of a compact multi-tool screwdriver set within easy reach, keeping them organized and readily accessible. ...Mounting securely to the wall allows it to stay out of sight while remaining effortlessly retrievable.

Opening on modem mount revised to provide extra room vertically due to Dremel use to shave off a little to fit it in. Update 4/25/2019, Printed and assembled with revisions needed to braces for backside. Everything looks and works great except for...

These are the same model I sell commercially for the ATEM Extreme (ISO). 2 versions, one that is designed to be use as a left and a right, same file, and it is the standalone. ...The other has a right and left, that is the bolt down which had extended...

This is a simple remix to allow a WAMIXIT 10.1 inch Display that was 1.3in and needed an additional lip. Added 2 holes for stability bars with a cold shoe adapter on top. Print 2 for use. ...Currently extends with bar to allow access to Mic 3.5mm input...

10 inch rack mount for Ubiquiti USW-Flex-Mini UniFi Switch

WIP***I needed a solution for grouping a mini-PC stack I have of 4 Thinkcentres.Maybe you don't have 4 PCs but it can still help stack a couple of them. Remix it, and cut it in half. There are already screw holes in the back of the chassis of each...

Inspired by https://www.thingiverse.com/thing:64847 and expanding on my Mini Rack Mount system (inspired by https://www.thingiverse.com/thing:1936196), I decided that if you're going to put a Raspberry Pi, some Arduinos in a rack, then what's more...

Center Body for Mini Buggy Steering Rack