atem mini extreme stand 3d models

Just a simple remix of the original ATEM Mini stand to fit the new larger ATEM Mini Extreme and Extreme ISO. Note: initial upload had an incorrect file for about an hour. ...v1.1 fixes that problem.

Designed with F360, this is a 20º Stand for the BlackMagic ATEM Mini Extreme and Extreme ISO. The height is 21mm in the front to allow a perfect fit between the ATEM and the StreamDeck if you want to use companion. This design includes: - 2...

Designed with F360, Stand for the BlackMagic ATEM Mini Extreme

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

I use the Shuttle HD with my ATEM Mini Extreme ISO and needed the ability to add a stand to the area with the SD Card/LAN port or add a mid-ATEM Extreme support when working on certain surfaces or needing additional accessory ports. This design...

... into the back. Prints fine with standard settings. No supports needed. This is a remix of two different designs from. Blackmagic ATEM Mini / Mini Pro Stand by natekrause May 31, 2020 BlackMagic ATEM MINI EXTREME STAND by joaofael April 05, 2022

I needed something similar for the ATEM Mini Extreme; I have not included fan adapters, just the basic mounts. These clip on to each side of the ATEM, with countersunk holes for M4 bolts to attach to a desk/rack shelf/etc. Many thanks to Spudd1 for...

Simple design based off my previous ones for the ATEM Mini. This is for the Extreme and Extreme ISO. ... Print on it's side, recommend 3 perimeters, PETg for strength or CF or Nylons

Designed to lift the ATEM mini (or pro) off the surface to keep it cooler, one simply sets it at an angle while the other raises it up about 10mm. To prevent slipping, use a thin rubber like neoprene under the feet. The new V2 model features only one...

These are the same model I sell commercially for the ATEM Extreme (ISO). 2 versions, one that is designed to be use as a left and a right, same file, and it is the standalone. ...The other has a right and left, that is the bolt down which had extended...

The human elevates the ATEM Mini and Mini Pro with a sturdy stand, holding them securely above the work surface. ...For optimal stability, secure the rubber grips from beneath the Mini onto the base of the stand.

The ATEM Mini-Pro runs extremely hot, and elevating the switcher produces a substantial improvement in cooling efficiency when running continuously. This design combines elements of two other stands, as I discovered that the angle of the ATEM top...

Holds Blackmagic Design ATEM Mini Extreme/ISO at angle to make it easier to access buttons for switching. Use 20x20 angle aluminum bar to join across the top with M4 nut/bolt. I'll update soon with recess for joiner on the bottom front and rear...

The file I found on Thingiverse only hold on to the edges of the Atem Mini Pro because my monitor else wouldn't fit. Made some little changes for my needs. ... This is a remix op a remix ;-) Original design:...

This is a Remix of the ATEM Mini Stand. I've added supports for a monitor so you can have more portability to your streaming setup. The support brackets can be slid on from either end so simply print two of them. ... Enjoy!

This versatile mounting solution streamlines the integration of the Blackmagic ATEM Mini Pro, a high-performance video switcher, into various settings. By providing a secure and adjustable attachment system, it enables users to easily mount and...

This mounting system is designed to facilitate cooling and quick-release mounting of the Blackmagic ATEM Mini Pro hardware video switcher. The objective is to facilitate flexible hard mounting with a convenient sliding quick release. ...More details to...

3d brackets ATEM Mini Pro

Rankmount for Blackmagic Atem Mini/pro

Here my design of an ATEM Mini Pro Decksaver - the cut-outs will fit to some of the availible stands/holders. Design free for changes. ...Non-Commerical - not for sale!

Mounting the Blackmagic Design Atem Mini is a solid approach that pays off immediately.

This cover will protect the buttons during travel, an ATEM Mini Pro is expensive enough ;-) If you like the design, tip me for a coffee!

Cover for Blackmagic's ATEM Mini and Mini Pro switchers. ...Two versions are included - one simple cover, and one hinged for easy access to the lower row of buttons.

Cover for Blackmagic's ATEM Mini and Mini Pro switchers. ...Two versions are included - one simple cover, and one hinged for easy access to the lower row of buttons.</p>

This is a pair of Urethane Feet to elevate a Blackmagic Design ATEM Mini off the flat surface and allow air flow under the bottom as well as elevating the back edge to form a more comfortable angle to use the switcher buttons. No tools are required...

Custom Case for Atem Mini and Monitor.\r\nFor more information on the parts needed for this case and how to build it, check out my full blog post here: https://dslrvideoshooter.com/atem-mini-case/\r\nWatch video demo of the case here:...

This is a cover (deck-saver) for the ATEM Mini (Pro & ISO as well), to stop dust from falling on the unit while not in use. The idea came from a similar thing I have for my Rodecaster Pro, which is really handy!. I've posted two versions, one...

I wanted a stand that would match the ATEM Mini Extreme Stand and allow me to attach them together. Users can use one of these to bind the ATEM Mini Extreme and Shuttle HD together, or use it as a standalone stand for the Shuttle HD. I have also...

This is a mount for the ATEM Mini Pro that allows it to be wall mounted.

There is a left and a righty. Lay it down flat, no supports, use 3 perimeters. ... PETg with ~20%+ gyroid is best