asp explorer model

They should easily fit even on small printers; if you can print Hadley, you can print this mount.The mount uses a vinyl disk that sits on top of teflon pads, for very smooth motion.It is very lightweight, and can easily disassembled for compact...

Depending on how well your models adhere to the print bed, you may need a brim/shaft/skirt to increase adhesion. In principle, it should be printable with any 3d printer, as I printed mine with my old Anycubic, which was about to break down...

If you want to be able to focus it, you'll need a helicoid that maintains or falls below M42's register distance of 47.46mm at its shortest for your camera setup. Disclaimer: This model is offered AS-IS with no guarantee that it will print for you as...

UPDATE: The model has been printed & test fit. Like a freakin' glove. #caliperlove Inserting the letters requires a bit of finesse & just enough brute force not to break the R and X apart- just be patient & make sure to clear any wisps/stringing in...

Please check the images to see what it is included in this kit.This set contains: - Cultists of Melmora (12)- Plague Knights (4 + 4)- Fosco – Herald of Melmora- Fallen Saint Mordentus – the Penitent- Blasphemia – Daughter of Decay (Cultist...

Based on the given specification for generating an OpenSCAD script that will output a specific shape model made of acrylic plates, here's the script: ```OpenSCAD $fa=5; $fs=0.5; color("gray"){ translate([4,16,-24]){ mirror([1,0,0]) mirror([0,0,1])...

4028 fan mount: Note this is modelled with internal supports in the top section of the duct to make it easier to print. Please remove these supports after printing. 4 x M3 32 mm (upper fan mount) 2 x M3 x 12 mm cap screws (lower fan mount) 6 x M3...

I have no immediate plans of adding a mount for a counterweight because everyone will find differently shaped ones _____________________ **Edit: ** Added an adjustable version of the speaker caps and a locking buckle ___________________ I wasn't...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 0 stencil_drawing =...

One intersting thing I probably should have done, is just print the columns on the platforms, would have saved some time, and the hardest assembly step. Next Acquire the Electrical components: Electrical Components Post Printing is very involved,...

If you use OpenSCAD, the model could be adjusted further refine the diameter of the internal air channel for your needs. Caution, because small changes in diameter produce big changes in airflow! Print Settings ========== The dimensions of...

 900mm in length (shown in the picture is a bit too long, you may want to use 800mm instead)The bamboo skewers seems to come in different sizes, so use the file that closest match the skewers you have and scale the model accordingly.  If...

 **Additional part sources** --- * [The Tensioner knob is a remix of donnyb99's CR-10 tensioner](https://www.thingiverse.com/thing:2168903/files) * [The tensioner itself was inspired by mukha521's AM8 tensioner but...

*** I do not want to come across as an erse, so I'm sure some will think I am when I say this - but I want to clearly point out that this is a CC ATTRIBUTION - _NON-COMMERCIAL_ - _NON-DERIVATIVE_ license - please let's enjoy the model, but please...

I created this project to get more experience in modelling for 3D printing using Fusion 360, practice my soldering skills, and get a chance to do a little ESP8266/Arduino programming. *Features* hang it from the wall using the built in hole(s) or...

Please check the images to see what it is included in this kit.This set contains: - Draconian Shock Troops (12)- Assault Dragons (4 + 4)- Commander Drakvarr- Flamagath Blackflame- Azgrathok - Chaos Dragonlord- Onixia the Tempest (Draconian Pinup)-...

I added some build notes below and a BOM which doesn't include screws, wires, connectors, etc., but has all major components. I planned to revisit this model and release a better version. However I have at least a year's worth of projects in...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

This is an OpenSCAD module library for propellers and spinners.This design models elliptical propeller blades that transition smoothly through three different NACA airfoils, starting with (by default) NACA 8430 at the hub radius, transitioning to...

I sliced it with Cura 4.4 so you can use per model settings to print the whole thing at once. I printed it at .15mm layer height.</p> <p>Here's a video of the toy with some details. ...The video has a lot of assembly photos at the end.<br/> <figure...

This is a servo hinge setup for use with MIPRESIDENT's Iron Man Mark III helmet (http://www.thingiverse.com/thing:260152). You can see my final build here: http://www.thingiverse.com/make:286759 And a video of it in use here:...

Verify the axle turns freely. Source File FreeCAD: BearingPegV4_2019.FCSTD Reinforced Within the pegs (excluding the original V4) 'pins' are embedded that promotes a strong cross pattern with lines at the stress point in addition to beveling....

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

Bear Exxa 1.0 is available here: https://www.thingiverse.com/thing:4362586 IMPORTANT: The Bear X axis will currently limit you to what alternative extruder/tool options you can mount without creating an adapter plate as it is different than previous...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

To connect this to the second hand holder disc, I bought a plastic tube of 1mm inner diameter from a modeling shop. I pinched one side a bit to make it flatter. This seems to work, but maybe I will have to glue it on the pin. I didn't do so yet...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 120-277V and 347V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Wiring: These LED light...

Summary Section:&nbsp;A partner and I worked together to design a 3D model for a ghost bookmark clip. Based off a doubled-scale diagram of an example bookmark marked up with original dimensions, we created the 2D sketch on the SOLIDWORKS program. We...

For the extruder I used from: https://www.thingiverse.com/thing:2735475/files cable-holder.stl https://www.thingiverse.com/download:4650325 extruder-cover.stl https://www.thingiverse.com/download:4650320 extruder-idler.stl...

the older model this was printed from did not have the pockets for the hex nuts so it was threaded directly into the plastic instead. Ive uploaded a reinforced version of the arm that should work better with heavier controllers.i also opened up the...